User manual SONY CDP-C67ES

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Press G/g to select (General Setup, ) then press ENTER or f on the remote. The options for "General Setup" appear. 2 Notes · When you play discs which have the parental control function, playback of the disc is limited on the Unit. · Depending on the disc, you may be asked to enter your password when playback starts. In this case, enter the password. 3 Press F/f to select an option, then press ENTER on the remote. The options for the selected item appear. 4 Press F/f to select an item, then press ENTER on the remote. TV Type Select the color system of the TV to be connected. The setup may be different in depending on regions or countries. The default setting is underlined. NTSC PAL AUTO Outputs the NTSC color system. Outputs the color system that is recorded on the disc. 28US TV Display Selects the aspect ratio of the connected TV screen (4:3 standard or wide). Depending on the disc, "Normal/LB" may be selected automatically instead of "Normal/PS" or vice versa. Normal/PS (4:3 PAN SCAN) Setting the language and playback restriction (Preference) Choose settings according to the TV to be connected. 1 Press DVD SETUP on the remote when the Unit is in stop mode. Press G/g to select (Preference, ) then press ENTER or f on the remote. The options for "Preference" appear. 2 Chapter 4 Playing Discs (DVP-NW50 only) Select this when you connect a 4:3 screen TV. · Tuning interval for direct tuning is: FM: 78. 50 MHz to 108. 00 MHz AM: 530 MHz to 1710 MHz 3 Chapter 5 Enjoying Radio and Other Component Press the "AM" (or "FM") SELECT, then press BACK. The display returns to the current frequency. 4 Press any SELECT. The display changes to the current frequency. 5 Press DOWN/UP on the remote to adjust the frequency. DOWN/UP Changes the current frequency to a frequency 1 step lower or higher. (Manual tuning) Scans a particular station toward a lower or higher frequency. Scanning stops automatically when the station is tuned in. (Automatic tuning) DOWN/UP (press and hold) When you know the frequency of the station Press the numeric buttons on the remote to enter the frequency (Direct tuning). Example: FM 105. 70 MHz 1t0t5t7t0 32US Presetting Radio Stations After you have tuned in stations using direct tuning or Automatic tuning, you can preset them to the Unit. Up to 20 FM or AM stations can be preset. Naming the Preset Stations You can edit the name of the preset stations in the Preset station list. 1 1 Press "TUNER" SELECT on the Home Menu. The display changes to the Tuner display, then the Preset station list appears. Press the "TUNER" SELECT on the Home Menu. The display changes to the Tuner display, then the Preset station list appears. Chapter 5 Enjoying Radio and Other Component 2 2 Press any SELECT that corresponds to the station you want to tune in. The display changes to the current station display. Tune in to the station that you want to preset (page 31). Press and hold any SELECT of the station of which you want to edit the name. [. . . ] , The signal strength of the stations is too weak (when tuning in with automatic tuning). , No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). , There are obstacles between the remote and the Unit. , The distance between the remote and the Unit is too far. [. . . ]