User manual SONY CDP-X399ES

[. . . ] Serial No. For the customers in the United States Except for customers in the United States This appliance is classified as a CLASS 1 LASER product. This marking is located on the rear exterior. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. AC power cord must be changed only at the qualified service shop. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. [. . . ] Press ANALOG OUT LEVEL +/­ on the remote. Getting Started 1 Press PLAY MODE repeatedly until the mode you want appears. Select To play CONTINUE SHUFFLE PROGRAM The CD in the original order. The tracks on the CD in the order you want them to be played (see "Programming the CD tracks" on page 12). Select a track directly Find a point in a track Playing CDs 2 Press H. Tip (CDP-XE570/XE370 only) Play tracks in random order Remove the CD Adjust the volume You can select the playing mode by pressing CONTINUE, SHUFFLE, or PROGRAM on the remote. Repeat Play Operations You can play the CD tracks repeatedly in any play modes. To activate the Repeat Play function, press REPEAT until "REPEAT' appears in the display. To Press REPEAT * When you directly locate a track numbered over 10, press >10 first, then the corresponding number buttons. Example: To play track number 30 Press >10 first, then 3 and 10. Tips Repeat only one track Until "REPEAT 1" appears while playing the track you want to repeat. Until "REPEAT" or "REPEAT1" disappears. Cancel Repeat Play When you are in the Repeat Play function, the player repeats the tracks as follows: When the disc is played in The player repeats · You can adjust the analog output level with the ANALOG OUT LEVEL +/­ on the remote (page 7) (CDP-XE570/XE370 only). · You can adjust the headphones volume on the remote. To adjust the volume, connect the headphones to the PHONES jack and adjust the volume with the ANALOG OUT LEVEL +/­ on the remote (CDP-XE570 only). · If there is no CD in the player, "­NO DISC­" (or "no dISC" for the CDP-XE370/XE270) appears in the display. Note Continuous Play Shuffle Play Programme Play (page 12) All the tracks All the tracks in random order The same programme If "­ OVER ­" (or " " for the CDP-XE370/ XE270) appears in the display, the disc has reached the end while you were pressing M. Press m or turn lAMSL counterclockwise to go back. 9 Using the CD display You can check information about the disc using the display. In the stop mode Press TIME/TEXT (or TIME for the CDPXE370/XE270 ). CDP-XE570 TRACK INDEX MIN SEC To check the remaining time Press TIME/TEXT (or TIME for the CDPXE370/XE270) during playback. Each time you press this button while playing a disc, the display changes as shown in the chart below. ­ ­" appears instead of the total playing time. · "PROGRAM FULL" (or "FULL" for the CDPXE370/XE270) appears in the display when you try to add a track to a programme which already contains 24 tracks. Change the whole Hold down CLEAR until programme "CLEAR" (for the CDP-XE570) completely or "CLEAr" (for the CDP-XE370/ XE270) appears in the display. Create a new programme following the programming procedure. 12 Recording From CDs (CDP-XE570 only) Fading In or Out (CDP-XE570/XE370 only) You can manually fade in or out to prevent tracks from starting or ending abruptly. Note that you cannot use this effect when you use the DIGITAL OUT (OPTICAL) connector. To Press FADER Recording a CD by Specifying Tape Length (Time Edit) You can have the player create a programme that will match the length of the tape. In this feature, the player creates a programme basically keeping the original order of the disc. However, the player may change the last track of each side to match the recording time to the tape length. i. e. Side A: track number Side B: track number 1t2t3t4t8 5t6t7t9t10 Start play fading in During pause. For the CDPXE570, "FADE" flashes. For FADE the CDP-XE370, lights up in the display and the Q indication flashes. End play fading out When you want to start fading out. For the CDP-XE570, "FADE" flashes. [. . . ] Do not use such discs. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. Notes on CDs On handling CDs · To keep the disc clean, handle the disc by its edge. · Do not stick paper or tape on the disc. On power sources · Before operating the player, check that the operating voltage of the player is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the player. · The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. [. . . ]