User manual SONY CDX-CA850X

[. . . ] Labels are attached Notes on handling CDs A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc by its edge. To keep the disc clean, do not touch the surface. To search backward To search forward Elapsed playing time Note To play back an 8 cm (3 in. ) CD, use the optional Sony compact disc single adapter (CSA-8). Note " or " " appears in the display, If " you have reached the beginning or the end of the disc and you cannot go any further. Notes on CD-R discs Do not stick paper or tape on the labeled surface. ·You can play CD-Rs (recordable CDs) on this unit. [. . . ] · When CD playback is stopped, you may hear some noise from the speakers. To prevent this from happening, turn the volume down before stopping CD playback. · If you leave the ejected disc in the disc insertion slot after you have pressed Z, the disc will automatically retract into the unit after about 15 seconds in order to protect it. When you play 8 cm (3 in. ) CDs Use the optional Sony compact disc single adapter (CSA-8) to protect the CD player from damage. Playing tracks in random order -- Shuffle Play Press (SHUF) during playback. "SHUF" appears in the display. To return to normal playback mode, press again. Before playing, clean the discs with a commercially available cleaning cloth. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog discs. Notes on moisture condensation On a rainy day or in a very damp area, moisture may condense on the lenses inside the CD player. Should this occur, the unit will not operate properly. In this case, remove the disc and wait for about an hour until the moisture evaporates. CDX-CA850X Sony Corporation 2000 Printed in Korea Changing the display item Each time you press (DSPL) during CD playback, the item changes as follows: Elapsed playing time b B Track number Changing the transmitting frequency Because this unit processes CD playback sound through an FM tuner, there may be interference noise during CD playback. In this case, change the frequency of the modulated RF signal transmitted from the unit. The initial setting is 88. 3 MHz. Changing the output level You can select the output level of the CD player. · The unit is installed at an angle of more than 60°. · The unit is not installed in a sturdy part of the car. Specifications AUDIO POWER SPECIFICATIONS >:, 4 3 Press (REPEAT) for more than two seconds. Press (REPEAT) for more than two seconds. CD cannot be loaded. The sound skips due to vibration. POWER OUTPUT AND TOTAL HARMONIC DISTORTION 13 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 1 % total harmonic distortion. Other specifications CD player section System Signal-to-noise ratio Frequency response Wow and flutter Laser Diode Properties Material Wavelength Emission Duration Laser output power Compact disc digital audio system 90 dB 10 ­ 20, 000 Hz Below measurable limit GaAs + GaAlAs 785 ~ 815 nm (Typ. 800 nm) Continuous Less than 0. 5 mW* Note Be sure to set the frequency of your FM tuner to the newly selected frequency. General Outputs Power requirements Current drain Dimensions Mounting dimensions Mass Supplied accessories Optional accessories Line output 12 V DC car battery (negative ground) 2 A (at disc loading) Approx. 178 × 50 × 173 mm (7 1/8 × 2 × 6 7/8 in. ) (w/h/d) Approx. 182 × 53 × 159 mm (7 1/4 × 2 1/8 × 6 3/8 in. ) (w/h/d) Approx. 7 oz. ) Parts for installation and connections (1 set) Compact disc single adapter CSA-8 Rotary commander RM-X4S Source selector XA-107 BUS cable (supplied with an RCA pin cord) RC-61 (1 m), RC-62 (2 m) CAUTION The use of optical instruments with this product will increase eye hazard. Error displays The following indications will flash for about five seconds. Display Cause A CD is dirty or inserted upside down. The CD player cannot be operated because of some problem. Solution Clean or insert the CD correctly. Press the reset button or Z. * This output is the value measured at a distance of 0. 7 mm from the objective lens surface on the Optical Pick-up Block. If the above-mentioned solutions do not help improve the situation, consult your nearest Sony dealer. Design and specifications are subject to change without notice. Connections Caution ·This unit is designed for negative ground 12 V DC operation only. ·Before making connections, disconnect the ground terminal of the car battery to avoid short circuits. [. . . ] ·Use only the supplied mounting hardware for a safe and secure installation. 1 TO P 2 Mounting angle adjustment Adjust the mounting angle to less than 60°. 4 5 6 Mounting example Installation in the dashboard max. size 5 × 6 mm ×2 1 TO P 182 mm (7 1/ 4 in. ) 2 53 m m (2 1/ 8 in . ) 3 7 (7/32 × 1/4 in. ) Reset button When the installation and connections are complete, be sure to press the reset button with a ball-point pen, etc. 7 8 9 6 1 Bend these claws, if necessary. Note To prevent malfunction, install only with the supplied screws 7. 6 6 7 AMS SHUF REPEAT ×4 DSPL OFF With the TOP marking up 7 max. size 5 × 6 mm (7/32 × 1/4 in. ) Caution Reset button Cautionary notice for handling the bracket 1. [. . . ]