User manual SONY CDX-GT454US

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. [. . . ] · TV/Video : TV n VIDEO1 n VIDEO2 n . . . Tip When the POWER SELECT switch is set to position B, you can turn on this unit by pressing (SOURCE) on the rotary commander. By rotating the control (the SEEK/ AMS control) Press (LIST) to display the memorised names. 12 Changing the operative direction The operative direction of controls is factoryset as in the illustration below. To increase Changing the sound and display settings You can set: · CLOCK (page 7). · D. INFO (dual information) to display the clock and the play mode at the same time (ON) or to display the information alternately (OFF). · AMBER/GREEN to change the illumination color to amber or green. · DIM (Dimmer) to change the brightness of the display. -- Select "ON" to dim the display. · BEEP to turn the beep tones on or off. · RM (Rotary Commander) to change the operative direction of the controls of the optional rotary commander. -- Select "NORM" to use the rotary commander in the factory preset position. -- Select "REV" when you mount the rotary commander on the right of the steering column. · A. SCRL (Auto Scroll) (page 14). Note If you connect an optional power amplifier and do not use the built-in amplifier, the beep tone will be disabled. To decrease If you need to mount the rotary commander on the right side of the steering column, you can reverse the controls operative direction. EN Other Function Press (SOUND) two seconds while pushing the VOL control. Tip You can control the operative direction of controls with the unit. 1 Press (SHIFT). Tip If the name of the MD is too long, you can scroll it across the display window by pressing (SHIFT), then (1) (N). 14 Automatically scrolling a disc name -- Auto Scroll If the disc name or track name on an MD exceeds 8 characters and the Auto Scroll function is on, automatically scrolls on the display as follows: Locating a specific point in a track -- Manual Search During playback, push the SEEK/AMS control up or down and hold for about two seconds. Release when you have found the desired point. SEEK/AMS · The disc name appears when the disc has changed (if the disc name is selected). · The track name appears when the track has changed (if the track name is selected). · The disc or track name appears depending on the setting when you press (SOURCE) to select an MD. To search forward To search backward If you press (DSPL) to change the display item, the disc or track name of the MD is scrolled automatically whether you set the function on or off. Locating a disc by disc number -- Direct Disc Selection Press the number button corresponding to the desired disc number. The desired disc in the currently selected changer begins playback. 1 2 3 Press (SHIFT), then press (2) (SET UP) repeatedly until "A. SCRL" appears. Press (4) (n) to select "A. SCRL-ON. " Press (SHIFT). Scanning the tracks -- Intro Scan You can play the first 10 seconds of all the tracks on the currently selected disc. EN Other Function/CD/MD Changer To cancel Auto Scroll, select "A. SCRL-OFF" in step 2 above. Displaying the recording date of the currently selected MD Press (DSPL) for two seconds during MD playback. The recording date of the track is displayed for about three seconds. 1 2 3 During playback, press (SHIFT), then press (3) (PLAY MODE) repeatedly until "INTRO" appears. Press (4) (n) to select "INTRO-ON. " Intro Scan starts. Press (SHIFT). Locating a specific track -- Automatic Music Sensor (AMS) During playback, push the SEEK/AMS control up or down once for each track you want to skip. To locate succeeding tracks To locate preceding tracks SEEK/AMS To go back to the normal playback mode, select "INTRO-OFF" in step 2 above. 15 Playing tracks repeatedly -- Repeat Play You can select: · REP-1 to repeat a track. · REP-2 to repeat a disc. Labeling a CD -- Disc Memo (CD changer with custom file function) You can label each disc with a personalized name. You can enter up to eight characters for a disc. [. . . ] ·Set the fader control to the center position for two-speaker systems. · The power cord or battery has been disconnected. · The reset button has been pressed. n Store again into the memory. The contents of the memory have been erased. Indications do not appear in the Remove the front panel and clean the connectors. [. . . ]