User manual SONY CD-X1150

[. . . ] · If no power is being supplied to the unit, check the connections first. If everything is in order, check the fuse. · If no sound comes from the speakers of a twospeaker system, set the fader control to the center position. [. . . ] If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. CAUTION The use of optical instruments with this product will increase eye hazard. 90° Do not expose the discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car. Fuse (10 A) Warning Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. *I-3-866-373-11*(1) Location of controls Setting the clock The clock has a 12-hour digital indication. Example: To set the clock to 10:08 Radio Memorizing stations automatically -- Best Tuning Memory (BTM) This unit selects the stations with the strongest signals and memorizes them in the order of their frequencies. You can store up to 6 stations on each band (FM I, FM II, FM III, and AM). 1 2 SOURCE BTM Press (DSPL) during operation. Press (DSPL) for two seconds. Memorizing only the desired stations You can store up to 6 stations on each band (a total of 18 for FM I, FM II, and FM III, and 6 for AM) in the order of your choice. If you cannot tune in a preset station Press either side of (SEEK/AMS) to search for the station (automatic tuning). Scanning stops when the unit receives a station. Press either side of (SEEK/AMS) repeatedly until the desired station is received. Note If the automatic tuning stops too frequently, press (SENS/BTM) repeatedly until "LOCAL" (local seek mode) is displayed. Only the stations with relatively strong signals will be tuned in. Tip If you know the frequency of the station you want to listen to, press and hold either side of (SEEK/AMS) until the desired frequency appears (manual tuning). SENS MODE SEEK AMS ATT SOUND REPEAT SHUF LOUD The hour indication flashes. OFF 1 2 3 4 5 6 DSPL 1 Set the hour. CDX-1150 1 2 3 4 Caution To go forward To go backward Press (SOURCE) repeatedly to select the tuner. Press (MODE) repeatedly to select the band. press and hold either side of (SEEK/AMS) to tune in the station that you want to store on the number button. Press and hold the desired number button ((1) to (6)) until "MEM" appears. The number button indication appears in the display. When tuning in stations while driving, use Best Tuning Memory to prevent accidents. 1 1 MODE (band select) button 2 SOURCE (source select) button 3 Reset button 4 (+) (­) (volume/bass/treble/left-right/ front-rear control) button 5 Display window 6 SEEK/AMS (seek/Automatic Music Sensor/ manual search) button 7 6 (eject) button 8 SENS/BTM (sensitivity adjust/Best Tuning Memory) button 9 ATT (attenuate) button 0 SOUND button !¡ During radio reception: Number buttons During CD playback: (1) REPEAT button (2) SHUF button !DSPL (display mode change/time set) TM button !¢ LOUD (loudness) button 2 Press (SOUND). Press (SOURCE) repeatedly to select the tuner. Each time you press (SOURCE), the mode changes as follows: CD ~ TUNER If FM stereo reception is poor -- Monaural Mode Press (SENS/BTM) repeatedly until "MONO" appears. The sound improves, but becomes monaural ("STEREO" disappears). [. . . ] During playback, press and hold either side of (SEEK/AMS) for about two seconds. To obtain the beep sound again, press these buttons again. Note If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Error displays The following indications will flash for about five seconds. Display Cause A CD is dirty or inserted upside down. [. . . ]