User manual SONY CD-X727

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. [. . . ] Rotate the control and release it to: ·Locate a specific track on a disc. Rotate and hold the control until you locate the specific point in a track, then release it to start playback. Rotate and hold the control to tune in a specific station. SOUND MODE LIST LIST MODE SOUND By pushing in and rotating the control (the PRESET/DISC control) Using the rotary commander By pressing buttons (the SOURCE and MODE buttons) Push in and rotate the control to: ·Receive the stations memorized on the number buttons. ·Change the disc. (MODE) (SOURCE) Each time you press (SOURCE), the source changes as follows: TUNER n CD n MD* n TV* * If the corresponding optional equipment is not connected, this item will not appears. Pressing (MODE) changes the operation in the following ways; · · · · Tuner: FM1 n FM2 n AM CD unit: CD1 n CD2 n . . . TV/Video: TV n Video1 n Video2 n . . . 15 Other operations Rotate the VOL control to adjust the volume. Press (ATT) to attenuate the sound. OFF Adjusting the sound characteristics You can adjust the equalizer curve, listening position, cut-off frequency, bass, treble, balance and fader. You can store the bass and treble levels independently for each source. Press (OFF) to turn off the unit. Press (SOUND) to adjust the volume and sound menu. 1 Select the item you want to adjust by pressing (SOUND) repeatedly. VOL (volume) n EQ* (equalizer curve) n POS* (listening position) n CNW* (crossover network) n SUB (subwoofer volume) n BAS (bass) n TRE (treble) n BAL (left-right) n FAD (rear-front) * If the corresponding optional equipment is not connected, this item will not appears. Press (LIST) to display the memorized names. 2 Changing the operative direction The operative direction of controls is factoryset as shown below. To increase Adjust the selected item by rotating the dial. Adjust within three seconds after selecting the item. (After three seconds, the dial function reverts the volume control. ) Attenuating the sound To decrease If you need to mount the rotary commander on the right-hand side of the steering column, you can reverse the operative direction. Press (ATT) on the supplied rotary commander or the supplied wireless remote. Press (3) (SET UP) repeatedly until the desired item appears. Each time you press (3) (SET UP), the item changes as follows: Clock n D. Info*1 n Amber/Green n Dimmer n Contrast n Voice*1 n Beep n RM n L. out*2 n Loud*1 n LPF*1 n M. dspl n English/French*1 n A. Scrl*1 *1 When the radio is off, or when no CD, or MD is playing this item will not appear. *2 When the optional equalizer preamplifier is not connected, this item will not appear. 3 Press (5) (n) to select the desired setting (Example: on or off). For the "Contrast" setting, pressing (5) (n) makes the contrast higher, and pressing (2) (N) makes the contrast lower. After the mode setting is complete, the display returns to normal playback mode. 4 17 Adjusting the frequency of the subwoofer(s) To match the characteristics of the connected subwoofer(s), you can cut out the unwanted high and middle frequency signals entering the subwoofer(s). By setting the cut-off frequency, the subwoofer(s) will output only low frequency signals so you can get a clearer sound image. Adjusting the sound and frequency of the equalizer This unit can also control an optional equalizer preamplifier. This lets you add some effects to the sound field of the currently selected source. For details, refer to the instructions manual supplied with the equalizer preamplifier. Note If you connect the optional digital preamplifier XDP-210EQ, the voice guide function will not work. 1 2 3 Press (SOURCE) to select a source (radio, CD or MD). Press (SHIFT), then press (3) (SET UP) repeatedly until "LPF" appears. Press (5) (n) or (2) (N) repeatedly to select desired setting. Changing the line output level You can change the line output level if you hear distortion or other noise. When the optional equalizer preamplifier is connected, you can set this function. SET UP Each time you press (5) (n) or (2) (N), the cut-off frequency in the display changes as follows: LPF off ~ LPF 80 Hz ~ LPF 120 Hz 1 2 3 Press (SHIFT), then press (3) (SET UP) until "L. out" appears. [. . . ] 1 oz. ) Rotary commander (1) Wireless remote (1) Parts for installation and connections (1 set) Front panel case (1) BUS cable (supplied with an RCA pin cord) RC-61 (1 m), RC-62 (2 m) Compact disc single adapter CSA-8 CD changer (10 discs) CDX-828, CDX-727 MD changer (6 discs) MDX-65 Other CD/MD changers with the Sony-BUS system Digital equalizer preamplifier XDP-210EQ Source selector XA-C30 TV tuner XT-40V, etc. Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessories * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. Tuner section FM 87. 5 ­ 107. 9 MHz External antenna connector 10. 7 MHz 8 dBf 75 dB at 400 kHz 50 dB at 200 kHz Signal-to-noise ratio 65 dB (stereo), 68 dB (mono) Harmonic distortion at 1 kHz 0. 7 % (stereo), 0. 4 % (mono) Separation 35 dB at 1 kHz Frequency response 30 ­ 15, 000 Hz Tuning range Antenna terminal Intermediate frequency Usable sensitivity Selectivity Optional accessories Optional equipment AM Tuning range Antenna terminal Intermediate frequency Sensitivity 530 ­ 1, 710 kHz External antenna connector 10. 71 MHz/450 kHz 30 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 ­ 8 ohms Maximum power output 45 W × 4 (at 4 ohms) Design and specifications are subject to change without notice. 31 Troubleshooting guide The following checklist will help you remedy the problems you may encounter with your unit. Before going through the checklist below, check the connections and operating procedures. General Problem No sound. Cause/Solution ·Cancel the ATT function. ·Set the fader control to the center position for two-speaker systems. [. . . ]