User manual SONY CD-X805

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. [. . . ] Press (ATT) to attenuate the sound. OFF Press (OFF) to turn off the unit. 12 Press (SOUND) to adjust the volume and sound menu. Adjusting the sound characteristics You can adjust the bass, treble, balance, and fader. You can store the bass and treble levels independently for each source. Press (LIST) to display the memorized names. 1 Select the item you want to adjust by pressing (SOUND) repeatedly. VOL (volume) n BAS (bass) n TRE (treble) n BAL (left-right) n FAD (front-rear) Changing the operative direction The operative direction of controls is factoryset as shown below. To increase 2 Adjust the selected item by rotating the dial. Adjust within three seconds after selecting the item. (After three seconds, the dial function reverts to volume control. ) To decrease If you need to mount the rotary commander on the right hand side of the steering column, you can reverse the operative direction. Attenuating the sound Press (ATT) on the optional rotary commander. To restore the previous volume level, press (ATT) again. Tip The unit decreases the volume automatically when a telephone call comes in (Telephone ATT function). Press (SOUND) for two seconds while pushing the VOL control. Tip You can also change the operative direction of these controls with the unit (page 14). 13 Changing the sound and display settings The following items can be set: ·CLOCK (page 6). ·D. INFO (Dual Information) - to display the clock and the play mode at the same time (ON) or to display the information alternately (OFF). ·AMBER/GREEN - to change the illumination color to amber or green. (CDX-C5750 only) ·DIM (Dimmer) - to change the brightness of the display. -- Select "ON" to dim the display. ·BEEP - to turn on or off the beeps. Press (2) (SET UP) repeatedly until "A. SCRL" appears. Press (4) (n) to select "A. SCRL-ON. " Press (SHIFT). CDX-C4750: Each time you press (DSPL) during CD/MD playback, the item changes as follows: $ Track number/ Elapsed playback time $ Disc name*1 $ Track name*2 $ Clock*3 To cancel Auto Scroll, select "A. SCRL-OFF" in step 3 above. Note For some CD TEXT discs with very many characters, the following cases may happen: -- Some of the characters are not displayed -- Auto Scroll does not work. Tip To manually scroll the long name of an MD or CD TEXT disc after activating the Auto Scroll function, Press (SHIFT), then (1) (N) (manual scroll). *1 If there is no prerecorded name for a CD or MD, "NO NAME" appears in the display. *2 If the track name of an MD is not prerecorded, "NO NAME" appears in the display. *3 If the dual information function is on, the clock does not appear in the display. Tip If the name of the MD is too long, you can scroll it across the display window by pressing (SHIFT), then (1) (N). Locating a specific track -- Automatic Music Sensor (AMS) During playback, push the SEEK/AMS control up or down and release for each track you want to skip. To locate succeeding tracks To locate preceding tracks SEEK/AMS After you select the desired item, the display will automatically change to the Motion Display mode after a few seconds. In the Motion Display mode, all the above items are scrolled in the display one by one in order. Tip The Motion Display mode can be turned off. (See "Changing the sound and display settings" on page 14). Locating a specific point in a track -- Manual Search During playback, push the SEEK/AMS control up or down and hold. Release when you have found the desired point. SEEK/AMS To search forward To search backward Automatically scrolling a disc name -- Auto Scroll (CDX-C5750 only) If the disc name, artist name, or track name on a CD TEXT disc or MD exceeds 8 characters and the Auto Scroll function is on, information automatically scrolls across the display as follows: · The disc name appears when the disc has changed (if the disc name is selected). · The track name appears when the track has changed (if the track name is selected). Locating a disc by disc number -- Direct Disc Selection Press the number button that corresponds with the desired disc number. The desired disc in the current unit begins playback. 16 Playing tracks repeatedly -- Repeat Play You can select: ·REP-1 - to repeat a track. [. . . ] ·Set the fader control to the center position for two-speaker systems. ·Rotate the dial in a clockwise direction to adjust the volume. · The power cord or battery has been disconnected. · The reset button has been pressed. [. . . ]