User manual SONY CD-XL250

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. [. . . ] Caution When tuning in stations while driving, use Best Tuning Memory to prevent accidents. Storing only the desired stations You can manually preset the desired stations on any chosen number button. SOURCE SRC MBP D-BASS MODE D OFF DISC REP SHUF BL SKIP ATA MTL SEEK AMS Storing stations automatically -- Best Tuning Memory (BTM) The unit selects the stations with the strongest signals within the selected band, and stores them in the order of their frequency. 1 Press (SRC) repeatedly to select the radio. 2 Press (MODE) repeatedly to select the band. The unit stores stations in the order of their frequencies on the number buttons. A beep sounds when the setting is stored. Notes · If only a few stations can be received due to weak signals, some number buttons will retain their former settings. · When a number is indicated in the display, the unit starts storing stations from the one currently displayed. 1 2 3 4 Press (SRC) repeatedly to select the radio. Press (MODE) repeatedly to select the band. Press either side of (SEEK/AMS) to tune in the station that you want to store. Press the desired number button ((1) to (6)) until "MEM" appears. The number button indication appears in the display. SEL ATT SENS 1 2 3 4 5 6 BTM DSPL CDX-L250 1 Volume +/­ button 2 MODE button 3 SRC (SOURCE) (TUNER/CD) button 4 SEL (select) button 5 Display window 6 MBP (My Best sound Position) button 7 D (D-BASS) button 8 Z (eject) button 9 Reset button q; ATT (attenuate) button qa SENS button qs Number buttons (3) REP (4) SHUF qd BTM (Best Tuning Memory) button qf DSPL (display mode change) button qg OFF button* qh SEEK/AMS +/­ button * Warning when installing in a car without an ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for 2 seconds to turn off the clock display after turning off the engine. Otherwise, the clock display does not turn off and this causes battery drain. Note If you try to store another station on the same number button, the previously stored station will be erased. CD Player Playing a disc Insert the disc (labeled side up). Other Functions Display items When the disc/track changes, any prerecorded title of the new disc/track is automatically displayed. Displayable items · Clock · Elapsed playing time Adjusting the sound characteristics You can adjust the bass, treble, balance, and fader. The bass and treble levels can be stored independently for each source. Quickly attenuating the sound Press (ATT). The "ATT" indicator appears in the display. To restore the previous volume level, press (ATT) again. Source 1 Playback starts automatically. If a disc is already inserted, press (SRC) repeatedly until "CD" appears to start playback. To Stop playback Eject the disc Skip tracks ­ Automatic Music Sensor Fast-forward/ reverse ­ Manual Search Press Z or (OFF) Z (SEEK/AMS) (. />) [once for each track] (SEEK/AMS) (m/M) [hold to desired point] Track number To Switch display item Press (DSPL) Select the item you want to adjust by pressing (SEL) repeatedly. Each time you press (SEL), the item changes as follows: BAS (bass) t TRE (treble) t BAL (left-right) t FAD (front-rear) Canceling the beep sound Press (6) while pressing (SEL) down. To activate the beep sound again, press these buttons again. Note If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. 2 Adjust the selected item by pressing either side of the volume +/­ button. Note Adjust within 3 seconds after selecting the item. Playing tracks repeatedly -- Repeat Play The current track will repeat itself when it reaches the end. During playback, press (3) (REP) repeatedly until "REP" indicator appears in the display. [. . . ] You can emphasize and adjust the bass sound easily with (D) (D-BASS) button. Level D. BASS-3 D. BASS-2 D. BASS-1 D. BASS-3 D. BASS-2 D. BASS-1 A program broadcast in stereo is heard in monaural. t Cancel monaural reception mode. Error displays Error displays The following indications will flash for a while. E-04 A CD is dirty or inserted upside down. E-99 The CD unit cannot be operated because of some problem. [. . . ]