User manual SONY CD-XL350

[. . . ] 3-227-643-11 (1) Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5 % total harmonic distortion. CD player section Signal-to-noise ratio Frequency response Wow and flutter Laser Diode Properties Material Wavelength Emission Duration Laser output power 90 dB 10 ­ 20, 000 Hz Below measurable limit GaAlAs 780 nm Continuous Less than 44. 6 µW* Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 ­ 8 ohms Maximum power output 50 W × 4 (at 4 ohms) General Outputs Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessory Audio output Power amplifier control Power antenna relay control Bass ±10 dB at 20 Hz Treble ±10 dB at 20 kHz 12 V DC car battery (negative earth) Approx. 178 × 50 × 176 mm (7 1/8 × 2 × 7 in. ) (w/h/d) Approx. 182 × 53 × 161 mm (7 1/4 × 2 1/8 × 6 3/8 in. ) (w/h/d) Approx. 10 oz. ) Parts for installation and connections (1 set) Front panel case (1) Card remote commander RM-X115 FM/AM Compact Disc Player Operating Instructions * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. Tuner section FM Tuning range Antenna terminal Intermediate frequency Usable sensitivity Selectivity Signal-to-noise ratio 87. 5 ­ 107. 9 MHz External antenna connector 10. 7 MHz 11 dBf 75 dB at 400 kHz 65 dB (stereo), 68 dB (mono) Harmonic distortion at 1 kHz 0. 7 % (stereo), 0. 5 % (mono) Separation 33 dB at 1 kHz Frequency response 30 ­ 15, 000 Hz Owner's Record Design and specifications are subject to change without notice. [. . . ] ·Be sure to observe the correct polarity when installing the battery. ·Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. 4 mm 2 Repeat step 1 for the right side. 3 Slide the unit out of its mounting. Main unit WARNING Back of the front panel Notes · For safety, turn off the engine before cleaning the connectors and remove the key from the ignition switch. · Never touch the connectors directly with your fingers or any metal device. Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. Location of controls Refer to the pages listed for details. Card remote commander RM-X115 Radio The unit can store up to 6 stations per band (FM1, FM2, FM3, and AM1, AM2). DSPL MODE Caution When tuning in stations while driving, use Best Tuning Memory to prevent accidents. PRESET SOURCE SRC MBP D-BASS MODE + D OFF DISC REP SHUF BL SKIP ATA MTL SEEK AMS SEEK­ SOURCE SEEK+ Storing stations automatically -- Best Tuning Memory (BTM) The unit selects the stations with the strongest signals within the selected band, and stores them in the order of their frequency. 1 Press (SRC) repeatedly to select the radio. SEL PRESET ­ RELEASE ATT SENS 1 2 3 4 5 6 BTM DSPL OFF CDX-L350 VOL + ­ ATT 1 Volume +/­ button 2 Receptor for the card remote commander 3 MODE button 4 SRC (SOURCE) (TUNER/CD) button 5 SEL (select) button 6 Display window 7 MBP (My Best sound Position) button 8 D (D-BASS) button 9 Z (eject) button q; RELEASE (front panel release) button qa RESET button (located on the front side of the unit, behind the front panel) qs ATT (attenuate) button qd SENS button qf Number buttons (3) REP (4) SHUF qg BTM (Best Tuning Memory) button qh DSPL (display mode change) button qj OFF button* qk SEEK/AMS +/­ button The corresponding buttons of the card remote commander control the same functions as those on this unit. 1 DSPL button 2 SOURCE button 3 SEEK (</, ) buttons 4 OFF button 5 VOL (+/­) buttons 6 MODE button 7 PRESET (+/­) buttons 8 ATT button Note If the unit is turned off by pressing (OFF) for 2 seconds, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip Refer to "Replacing the lithium battery" for details on how to replace the batteries. 2 Press (MODE) repeatedly to select the band. The unit stores stations in the order of their frequencies on the number buttons. A beep sounds when the setting is stored. Notes · If only a few stations can be received due to weak signals, some number buttons will retain their former settings. · When a number is indicated in the display, the unit starts storing stations from the one currently displayed. * Warning when installing in a car without an ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for 2 seconds to turn off the clock display after turning off the engine. Otherwise, the clock display does not turn off and this causes battery drain. CD Player Playing a disc Insert the disc (labeled side up). Other Functions Display items When the disc/track changes, any prerecorded title of the new disc/track is automatically displayed. Scanning stops when the unit receives a station. Press either side of (SEEK/AMS) repeatedly until the desired station is received. Local Seek Mode: If the automatic tuning stops too frequently, press (SENS) repeatedly until "LCL" indicator appears. The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. CD playback A disc cannot be loaded. · The CD is forcibly inserted upside down or in the wrong way. · You tried to playback a CD-R not designed for audio use. · Some CD-Rs may not play due to its recording equipment or the disc condition. The ambient temperature exceeds 50°C. · The unit is installed at an angle of more than 60°. [. . . ] · The broadcast signal is too weak. · Connect a power antenna control lead (blue) or accessory power supply lead (red) to the power supply lead of a car's antenna booster. (Only when your car has built-in FM/AM antenna in the rear/side glass. ) · Check the connection of the car antenna. · The auto antenna will not go up. [. . . ]