User manual SONY CFD-E75

[. . . ] 3-228-965-11 (1) CD Radio Cassette-Corder Operating Instructions CFD-E75 © 2001 Sony Corporation Warning To prevent fire or shock hazard, do not expose the player to rain or moisture. Information For customers in the United States This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Each time you press DSPL·ENT MEM, a stored setting is displayed in the set order. To change the setting, display the setting you want to change and re-enter it. 3 20 To use the player before a timer playback starts Just turn on the player, and then you can use it. If you turn off the player before the preset time, timer playback will start at the preset time. In case of the radio, however, if you listen to the station which is different from the one you tuned in step 1 on page 20, you will hear that station at the preset time. Make sure to tune in the station you want to listen to before you turn off the player. To stop play Press POWER to turn off the power. Notes · When you press STANDBY in step 7, make sure that n or z button of the tape player is not pressed. · When you press n or z button of the tape player in the timer mode: If the tape length of one side is longer than the set time, the player will be turned off at the end of the tape, not at the set time. Tips · To exit the standby mode, press STANDBY to make c disappear from the display. · The preset settings remain until you reset them. Falling asleep to music You can set the player to turn off automatically after 10, 20, 30, 60, 90, and 120 minutes, allowing you to fall asleep while listening to music. MENU ALARM DSPL ENT MEM Jog dial The Timer 1 2 3 Play the music source you want. Press MENU·ALARM until "SLEEP" appears in the display, and press DSPL·ENT MEM. Turn the jog dial to select the minutes until the player goes off automatically. Each time you turn the jog dial, the indication changes as follows: "60" t "90" t "120" t "OFF" t "10" t "20" t "30. " continued 21 Falling asleep to music (continued) To cancel the sleep function Press POWER to turn off the power. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. Tips · You can fall asleep and wake up to different music. Set the waking up timer first (see page 20), turn on the power, and then set the sleeping timer. However, you cannot store different radio stations. · You can set different volume for the waking up timer and the sleeping timer. For instance, you can sleep at lower volume and wake up at higher volume. Using the countdown timer You can set the player to sound music or beep after a preset period of time, which is useful as a kitchen timer, etc. MENU ALARM Jog dial DSPL ENT MEM 1 2 Press MENU·ALARM for 2 seconds until "ALARM" appears in the display. Turn the jog dial to display the time (OFF, 1 to 60 minutes) for the alarm and press DSPL·ENT MEM. 3 Turn the jog dial to select the volume of the sound and press DSPL·ENT MEM. Display LO HI Volume low high 22 4 Turn the jog dial to select the sound for the alarm by and press DSPL·ENT MEM. Display bEEP MUSIC Sound for alarm beep "La primavera (Spring)" from "Le Quattro Stagioni (The Four Seasons)" by Vivaldi 5 Press DSPL·ENT MEM to turn on the countdown timer. The countdown timer starts to count down the time. After the preset period of time, the alarm will sound for about 20 seconds. The Timer To stop the alarm Press MENU·ALARM. Tip Because the settings are stored, you can turn on the countdown timer by pressing MENU·ALARM for about 2 seconds and then DSPL·ENT MEM. Be sure that "ALARM" appears in the display. 23 Setting Up Choosing the power sources You can use the AC power or batteries as a power source. 13 Battery compartment AC IN 2 to a wall outlet 1 Inserting the back-up batteries Insert three size AA (R6) batteries (not supplied) into the battery compartment. These batteries work to save the memory data. Replacing batteries Take out the batteries as illustrated. Note Before you replace the batteries, be sure to take out the CD from the player. [. . . ] · Replace all the batteries in the remote with new ones if they are weak. · Make sure that you are pointing the remote at the remote sensor on the player. · Remove any obstacles in the path of the remote and the player. · Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. [. . . ]