User manual SONY CFD-Z110

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. [. . . ] Press PRESET + or ­ to tune in the stored station. TheRadio 19 The Timer Setting the clock "­ ­:­ ­" indication appears in the display until you set the clock. CLOCK DSPL ENT MEM TUNE TIME SET ­, + Tip The time display system: 12-hour system AM 12:00 = midnight PM 12:00 = noon Before you set the clock, connect the power source (see page 26). 1 Press CLOCK for 2 seconds until the hour digit flashes. 2 Press TUNE TIME SET + or ­ until you set the current hour. Set the minutes by pressing TUNE TIME SET + or ­ until the correct minute is displayed. , 3 Press DSPL ENT MEM. The clock starts from 00 seconds. 20 The Timer Waking up to music You can wake up to music or a radio program at a preset time. Make sure you have set the clock ("Setting the clock" on page 20). STANDBY TIMER DSPL ENT MEM TUNE TIME SET ­, + The Timer Before you begin, make sure the c(clock) indication is not lit in the display. If it is lit, press STANDBY. 1 Prepare the music source you want to play. To play the radio a CD Do this Tune in a station Insert a CD 2 3 4 Press TIMER. The c(clock) and the music source ("Cd" or "RAdIO") flash. Select the music source ("Cd" or "RAdIO") by pressing TUNE TIME SET + or ­, then DSPL ENT MEM. Set the timer to the hour you want the music to start by pressing TUNE TIME SET + or ­, then DSPL ENT MEM. Set the minutes, then press DSPL ENT MEM. 5 Set the timer to the hour and the minutes you want the music to go off. (Do as step 4. ) continued The Timer 21 Waking up to music (continued) 6 Press TUNE TIME SET + or ­ to set the volume, then DSPL ENT MEM. Tips · To exit the standby mode, press STANDBY to make cdisappear from the display. · The preset settings remain until you reset them. Note When you press N or z button of the tape player in the timer mode: If the tape length of one side is longer than the set time, the player will be turned off at the end of the tape, not at the set time. 7 Press STANDBY. On power sources · For AC operation, use the supplied AC power cord; do not use any other type. · The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. · Unplug the player from the wall outlet when it is not be used for an extended period of time. · For battery operation, use six size D (R20) batteries. · When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. · The nameplate indicating operating voltage, power consumption, etc. On placement · Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. · Do not place the player on an inclined or unstable place. · Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. · If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. [. . . ] · Replace all the batteries with new ones if they are weak. Radio The picture of your TV becomes unstable. The tape does not move when you press an operation button. The REC z button does not function/The tape does not play. The tape does not erase completely. Tape Player · The source which was recorded on TYPE II (high position) or TYPE IV (metal) tape using this unit is being played. [. . . ]