User manual SONY CFD-503

[. . . ] The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. [. . . ] Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. On operation Precautions 2 to a wall outlet 1 to AC IN Discs that this unit CAN play Audio CD CD-R/CD-RW (CD-DA*) * CD-DA is the abbreviation for Compact Disc Digital Audio. It is a recording standard used for Audio CDs. Notes on cassettes Connect the AC power cord or insert six R14 (size C) batteries (not supplied) into the battery compartment . Notes Discs that this unit CANNOT play Side A Replace the batteries when the OPR/BATT indicator dims or when the unit stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the unit. To use the unit on batteries, disconnect the AC power cord from the unit. CD-R/CD-RW other than those recorded in music CD format CD-R/CD-RW of poor recording quality, CD-R/CD-RW that has scratches or are dirty, or CD-R/CD-RW recorded with an incompatible recording device CD-R/CD-RW which is finalized incorrectly Tab for side B Tab for side A Notes on discs Note for customers in Europe The unit automatically turns off after 30 minutes if no operation is performed after playback or recording for CD, TAPE or AUDIO IN. Before playing, clean the CD with a cleaning cloth. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error. The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback. Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. Cleaning the cabinet Specifications CD player section System Compact disc digital audio system Laser diode properties Emission duration: Continuous Laser output: Less than 44. 6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture. ) Number of channels 2 Frequency response 20 Hz - 20, 000 Hz +1/­2 dB Wow and flutter Below measurable limit Frequency response TYPE I (normal): 80 Hz - 10, 000 Hz General Radio section Frequency range FM: 87. 5 MHz - 108 MHz AM: 531 kHz - 1, 602 kHz IF FM: 128 kHz AM: 45 kHz Antennas FM: Telescopic antenna AM: Built-in ferrite bar antenna Speaker Full range: 8 cm dia. , 4 , cone type (2) Outputs Headphones jack (stereo minijack): For 16 - 32 impedance headphones Input AUDIO IN jack (stereo minijack) Power output 1. 7 W + 1. 7 W (at 4 , 10% harmonic distortion) Power requirements For CD radio cassette-corder: Thailand model: 220 V AC, 50 Hz Other models: 230 V AC, 50 Hz 9 V DC, 6 R14 (size C) batteries Power consumption AC 13 W Battery life For CD radio cassette-corder: Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. Do not stick paper or sticker on the CD, nor scratch the surface of the CD. Other models: Press POWER . Note When turning on the power, hold down OPERATE (or POWER) until OPR/BATT indicator lights up. If an FM broadcast is noisy, changing the current status to monaural usually reduces the noise. "St" or "Mo" appears. 2 While "St" is displayed, press MODE to display "Mo. " jack of the portable digital music player or other components using an audio connecting cable (not supplied). Selecting a CD play mode Press MODE (press , then press MODE during playback) until " 1", " ", "SHUF", "SHUF" and " ", "PGM", or "PGM" and " " appear in the display. Then proceed as follows: To Select Repeat a single track Select " 1" Then do this Press or to select the track that you want to repeat, then press . Press . 2 Press OPERATE (or POWER) to turn the unit on. 4 Press AUDIO IN and start playback on the connected component. The sound from the connected component is output from the speakers of this unit. Playing a tape 1 Press OPERATE (or POWER) . 3 Press , and insert the tape into the tape To connect the unit to a TV or VCR, use an extension cable (not supplied) with a stereo-mini jack on one end and two phono plugs on the other end. Tip You can record the sound of the connected component. Insert a blank tape and press . To adjust the volume Press VOLUME +, ­ . To listen through headphones Connect the headphones to the (headphones) jack on the back of the unit. compartment with the side you want to play facing upward. There is a problem with the quality of the CD-R/CD-RW, recording device or application software. Replace all the batteries with new ones if they are weak. [. . . ] You can play the same program again, since the program is saved until you open the CD compartment. After you have created the program, insert a blank tape and press to start recording. The resume function does not work during shuffle play or program play. Reorient the antenna to improve FM reception. 4 Press to start recording To ( is depressed automatically). Press . (forward) or (backward) in pause and hold it until you find the point then press . [. . . ]