User manual SONY CFD-535

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. [. . . ] To change the current program Press p once if the CD is stopped and twice if the CD is playing. Then create a new program following the programing procedure. The CD Player 17 The CD Player Enjoying sound effects (LOOP/FLASH) You can repeat part of a CD (LOOP) and can "flash" the CD sound (FLASH) during playback. STANDBY SLEEP CD/RADIO POWER (AC ONLY) MODE 0/10 10 VOL BAND TUNE FUNCTION TUNE LOOP FLASH SOUND LOOP FLASH On the remote Press LOOP·AUTO PRESET instead of LOOP. 1 2 Play a CD. Press and hold LOOP or FLASH at the point you want to start the function. To repeat a selected part of a CD "flash" the CD sound Press and hold LOOP FLASH To cancel the LOOP or FLASH function Release the button. The player returns to normal play. 18 The CD Player The Radio Presetting radio stations You can store radio stations into the player's memory. You can preset up to 20 radio stations, 10 for each band in any order. RADIO BAND DISPLAY ENT MEMORY LOOP AUTO PRESET PRESET +, ­ The Radio 1 2 Press RADIO BAND until the band you want appears in the display. Hold down LOOP·AUTO PRESET for 2 seconds until "AUTO" appears in the display. The stations are stored in memory from the lower frequencies to the higher ones. On the remote 1 Press BAND until the band you want appears in the display. 3 Hold down the number buttons that you want to preset the new station on for about 2 seconds. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 3 Hold down DISPLAY ENT·MEMORY for about 2 seconds. 4 Press PRESET + or ­ until the preset number (1 to 10) you want for the station flashes in the music calender. Then the power will go off at the preset time, and the player will enter into the standby mode. To use the player on batteries, disconnect the AC power cord from the player. 26 Setting Up Selecting the audio emphasis (SOUND/MEGA BASS) You can adjust the audio emphasis of the sound you are listening to. STANDBY SLEEP CD/RADIO POWER (AC ONLY) MODE 0/10 10 VOL BAND TUNE FUNCTION TUNE Setting Up LOOP FLASH SOUND MEGA BASS SOUND Selecting the sound characteristic Press SOUND repeatedly to select the audio emphasis you want. Choose ROCK POP LIVE VOCAL OFF To get powerful, clean sounds, emphasizing low and high range audio light, bright sounds emphasizing high and middle range audio percussive sounds, emphasizing bass audio the presence of vocals, stressing middle range audio the whole dynamic range for music such as classical music Reinforcing the bass sound Press MEGA BASS. "MEGA BASS" appears in the display. To return to normal sound, press the button again. Setting Up 27 Additional Information Precautions On safety · As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. · Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. On power sources · For AC operation, use the supplied AC power cord; do not use any other type. · The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. · Unplug the player from the wall outlet when it is not to be used for an extended period of time. · For battery operation, use six size D (R20) batteries. · When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. · The nameplate indicating operating voltage, power consumption, etc. [. . . ] · If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV. 30 Additional Information Radio Symptom The tape does not move when you press an operation button. The REC r button does not function/The tape does not play. The tape does not erase completely. Remedy · Close the tape compartment securely. · Make sure the safety tab on the cassette is in place. [. . . ]