User manual SONY CFM-20

[. . . ] However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed. The use of optical instruments with this product will increase eye hazard. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] To return to normal sound, press the button again. player goes off automatically. Each time you press the button, the indication changes as follows: "60" "90" "120" "OFF" "10" "20" "30". To cancel the sleep function Note Press POWER to turn off the power. When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. Speaker Full range: 8 cm (3 1/4 inches) dia. , 4 , cone type (2) Outputs Headphones jack (stereo minijack): For 16 - 32 impedance headphones Power output 1. 7 W + 1. 7 W (at 4 , 10% harmonic distortion) Power requirements For CD radio cassette-corder: 120 V AC, 60 Hz 9 V DC, 6 R14 (size C) batteries Power consumption AC 13 W Basic Operations To Select Program play Select "PGM" Then do this Press or then press DISPLAY·ENTER for the tracks you want to program in the order you want up to 20 tracks. Then press . On placement · Do not leave the player in a location near heat sources, in a place subject to direct sunlight, excessive dust or mechanical shock or in a car subject to the direct rays of the sun. · Do not place the player on an inclined or unstable place. · Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. · Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. Playing a tape 1 Press TAPE (direct power-on). 2 Press , and insert the tape into the tape compartment with the side you want to play facing you. Make sure there is no slack in the tape to avoid damaging the tape or the unit. On operation · If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. Move the portable telephone, etc. , away from the player. 3 Press to start recording ( is depressed automatically). To Press . . CD player The CD does not play or "no dISC" is displayed even when a CD is in place. · Place the CD with the label surface up. · Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. · There is a problem with the quality of the CD-R/CD-RW, recording device or application software. · Replace all the batteries with new ones if they are weak. 2 Hold down TUNE + or ­ until the frequency Pause recording Stop recording Tips you find the point. (forward) or (backward) in pause and hold it until you find the point. PUSH OPEN/CLOSE Tip Using the display To check the total track number and playing time Press DISPLAY·ENTER in stop mode. If the FM broadcast is noisy, press MODE until "Mono" appears in the display and radio will play in monaural. · Adjusting the volume or the audio emphasis will not affect the recording level. · For the best results, use wall outlet as a power source for recording. · To erase a recording, proceed as follows: 1 Insert the tape whose recording you want to erase. 3 Press . The sound drops out. · Reduce the volume. · Clean the CD, or replace it if the CD is badly damaged. [. . . ] Failure to clean the tape heads can cause degraded sound quality or an inability of the unit to record or play tapes. For details, refer to the instructions of the cleaning cassette. · The TYPE II (high position) or TYPE IV (metal) tape is being used. · Demagnetize the heads using a commercially available tape head demagnetizer. [. . . ]