User manual SONY CKM-NWZE430 DATASHEET

[. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Notice If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the communication cable (USB, etc. ) again. 2 For customers in the U. S. A. If you have any questions about this product, you may call: Sony Customer Information Center 1-800-222SONY (7669). The number below is for the FCC related matters only. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] If you insert the connectors forcibly, they may be damaged, and cause a malfunction of your camcorder. 77 Using a Computer Troubleshooting If you run into any problems using your camcorder, use the following table to troubleshoot the problem. If the problem persists, remove the power source and contact your Sony dealer. Overall operations/Easy Handycam The power does not turn on. · The battery pack is discharged, running low, or not attached to the camcorder. · Attach a charged battery pack to the camcorder (p. · Use the AC Adaptor to connect to a wall outlet (p. · Insert your camcorder into the Handycam Station correctly (p. 10). The camcorder does not operate even when the power is set to on. · Disconnect the AC Adaptor from the wall outlet or remove the battery pack, then reconnect it after about 1 minute. If the functions still do not work, press the RESET button (p. (If you press the RESET button, all settings, including the clock setting, are reset, except the Personal Menu items. ) Buttons do not work. · During Easy Handycam operation, the available buttons are limited (p. 20). You cannot turn Easy Handycam operation on or off. · During recording or communicating with another device via USB cable, you cannot turn Easy Handycam operation on or off. Settings change during Easy Handycam operation. · During Easy Handycam operation, the settings of the functions that are not displayed on the screen return to their defaults. Previously made settings are restored when you cancel the Easy Handycam operation. [DEMO MODE] does not start. · Eject the cassette and "Memory Stick Duo" from your camcorder (p. 18). The camcorder gets warm. · This is because the power has been turned on for a long time. 94). The picture remains on the LCD screen. · This occurs if you disconnect the AC Adaptor from the wall outlet or remove the battery pack without turning off the power first. This is not a malfunction. You cannot turn the LCD backlight off. · During Easy Handycam operation (p. 20), you cannot turn the LCD backlight on/off using the DISP/BATT INFO. The buttons do not appear on the touch panel. · Touch the LCD screen lightly. · Press DISP/BATT INFO on your camcorder (or DISPLAY on the Remote Commander) (p. 16). The buttons on the touch panel do not work correctly or do not work at all. · Adjust the screen ([CALIBRATION]) (p. 106). Cassette tapes The cassette cannot be ejected from the compartment. · Make sure the power source (battery pack or AC Adaptor) is connected correctly (p. · Remove the battery pack from the camcorder, then attach it again (p. · Attach a charged battery pack to the camcorder (p. 10). The cassette is not ejected even when the cassette lid is open. · Moisture condensation is starting in your camcorder (p. 105). The Cassette Memory indicator or title display does not appear while using a cassette with Cassette Memory. · This camcorder does not support Cassette Memory, so the indicator does not appear. 80 The remaining tape indicator is not displayed. · Set [ REMAINING] to [ON] to always display the remaining tape indicator (p. 52). The cassette is noisier during rewinding or fast-forwarding. · When using the AC adaptor, rewind/fast forward speed increases (compared with battery operation) and therefore increases noise. "Memory Stick Duo" You cannot operate functions using the "Memory Stick Duo. " · Slide the POWER switch down to turn on the CAMERA-MEM or PLAY/EDIT lamp (p. [. . . ] 12, 45 112 U USB jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 USB Streaming USB-CAMERA . . . . . . . . . . . . 51 USB-PLY/EDT (USB-Play/Edit). . . . . . . . . . . . 51 Using abroad . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]