User manual SONY CMT-EH25

[. . . ] 3-874-279-11(1) Micro HI-FI Component System Operating Instructions CMT-EH26 CMT-EH25 © 2008 Sony Corporation WARNING To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. [. . . ] Use buttons on the remote to control the Play Timer. Make sure you have set the clock. Select the sound source. Press / repeatedly until the desired sound source appears, and then press ENTER . The display shows the timer settings. 7 Press / to turn off the system. The system turns on 15 seconds before the preset time. If the system is on at the preset time, the Play Timer will not play. To activate or check the timer again 1 Prepare the sound source. Prepare the sound source, and then press VOLUME +/ to adjust the volume. To start from a specific track or file, create your own program (page 19). Press CLOCK/TIMER SELECT , press / repeatedly until "PLAY SEL" appears, and then press ENTER . To cancel the timer 2 3 Press CLOCK/TIMER SET . Press / repeatedly to select "PLAY SET, " and then press ENTER . "ON TIME" appears, and the hour indication flashes. Repeat the same procedure as above until "OFF" appears, and then press ENTER . To change the setting Start over from step 1. Tip The Play Timer setting remains as long as the setting is not canceled manually. 1GB Others Troubleshooting 1 Make sure the power cord and speaker cords are correctly and firmly connected. below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. Severehumornoise. Move the system away from sources of noise. Connect the system to a different wall socket. Install a noise filter (available separately) to the power cord. Remove any obstacles between the remote and the remote sensor on the unit, and position the unit away from fluorescent lights. Point the remote at the system's sensor. TheSTANDBYindicatorremainslit afterunpluggingthepowercord. The STANDBY indicator may not turn off immediately after unplugging the power cord. The indicator will turn off after about 40 seconds. 2 Find your problem in the checklist IftheSTANDBYindicatorflashes Immediately unplug the power cord, and check the following items. If your system has a voltage selector, is the voltage selector set to the correct voltage? Are you using only the supplied speakers? Is anything blocking the ventilation holes on the sides or back of the system?After the STANDBY indicator stops flashing, reconnect the power cord, and turn on the system. [. . . ] In this situation, turn off the TV, wait 15 to 30 minutes, and turn it back on. If there is no improvement, move the speakers far away from the TV. Cleaningthecabinet Clean this system with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as thinner, benzine, or alcohol. GB Topreventatapefrombeing accidentallyrecordedover Break off the cassette's overwrite protection tab from side A or B as illustrated. Break off the cassette tab Specifications Main unit Amplifier section European and Russian models: DIN power output (rated): 4 + 4 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 5 + 5 watts (4 ohms at 1 kHz, 10% THD) Music power output (reference): 7 + 7 watts (4 ohms at 1 kHz, 10% THD) Other models: DIN power output (rated): 4 + 4 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 5 + 5 watts (4 ohms at 1 kHz, 10% THD) Inputs: AUDIO IN (stereo mini jack): voltage 800 mV, impedance 47 kilohms (USB) port: Type A, maximum current 500 mA Outputs: PHONES (stereo mini jack): accepts headphones of 8 ohms or more SPEAKER: accepts impedance of 4 ohms To later reuse the tape for recording, cover the broken tab with adhesive tape. [. . . ]