User manual SONY CMT-FX250

[. . . ] Unit Getting Started Listening to the radio 1 Select "DAB" or "TUNER FM. " Press TUNER/BAND repeatedly. Creating your own program (Program Play) 1 Select the CD function. Press CD . 2 Perform tuning. For automatic scanning Press TUNING MODE repeatedly until "AUTO" appears, and then press +/ . Scanning stops automatically when a station is tuned in, and "ST" (for stereo programs only) lights up in the display. 2 Select the play mode. Press PLAY MODE repeatedly until "PGM" appears while the player is stopped. 3 Select the desired track or file number. Press / repeatedly until the desired track or file number appears. When programming MP3 files, press + / repeatedly to select the desired folder, and then select the desired file. If the scanning for an FM station does not stop, press to stop scanning, then perform manual tuning (below). When you tune in a DAB station or an FM station that provides RDS services, the service name or station name appears on the display. Selected track or file number Remote DAB/FM lead antenna (Extend it horizontally. ) To right speaker To wall outlet Speaker cord (Red/) Speaker cord (Black/) To left speaker For manual tuning (FM band only) Press TUNING MODE repeatedly until "MANUAL" appears, and then press +/ repeatedly to tune in the desired station. Notes on DAB stations When tuning in a DAB station, it may take a few seconds before you hear any sound. [. . . ] No TEXT (DAB only) : There is no text information in the received service. NOT USED : You tried to perform a specific operation under conditions where that operation is prohibited. OVER : You have reached the end of the disc while pressing during playback or pause. PUSH SELECT : You tried to set the clock or timer during timer operation. PUSH STOP : You pressed PLAY MODE during playback. SET CLOCK : You tried to select the timer when the clock is not set. SET TIMER : You tried to select the timer when the Play Timer is not set. TIME NG : The Play Timer start and end times are set to the same time. Precautions Discs that this system CAN play Audio CD CD-R/CD-RW (audio data/MP3 files) Specifications Mainunit Amplifiersection DIN power output (rated): 4 watts + 4 watts (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 5 watts + 5 watts (4 ohms at 1 kHz, 10% THD) Music power output (reference): 9 watts + 9 watts Sleep Timer: 2 Turn down the volume. Press VOLUME . 3 Select the AUDIO IN function. Press AUDIO IN . You can fall asleep to music. This function works even if the clock is not set. If you select "AUTO, " the system automatically turns off after the current disc stops, or within 100 minutes. 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. Discs that this system CANNOT play If "PROTECT" appears on the display 4 Start playback. Start playback of the connected component and adjust the volume. Note The system may enter standby mode automatically if the volume level of the connected component is too low. Adjust the component's volume accordingly. See "To turn off the automatic standby function. " Play Timer: You can wake up to CD or DAB/FM reception at a preset time. Make sure you have set the clock. 1 Prepare the sound source. Prepare the sound source, and then press VOLUME +/ to adjust the volume. To start from a specific CD track or audio file, create your own program. Immediately unplug the power cord, and check the following items after "PROTECT" disappears. Are the + and speaker cords short-circuited? Is anything blocking the ventilation holes of the system?After you have checked these above items and found to be all right, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. DAB radio station is not received properly. Adjusting the sound To Adjust the volume Generate a more dynamic sound (Dynamic Sound Generator X-tra) Set the sound effect Press VOLUME +/ . DSGX on the unit. 2 Select the timer set mode. Press CLOCK/TIMER SET . General The system does not turn on. Is the power cord plugged in? Check all antenna connections, then perform the DAB Automatic Scan procedure (see "Reception of DAB radio station"). The current DAB service may not be available. Press +/ to select a different service. [. . . ] Hold down while the system is on, until "AUTO. To turn on the function, repeat the procedure until "AUTO. STBY ON" appears. Notes "AUTO STANDBY" lights up in the display when the automatic standby function is turned on. The automatic standby function is invalid for the tuner functions (DAB/FM), even when "AUTO STANDBY" lights up in the display. [. . . ]