User manual SONY CMT-GP5

[. . . ] 4-246-842-11(1) Micro Hi-Fi Component System Operating Instructions Owner's Record The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Serial No. CMT-GP5 ©2003 Sony Corporation WARNING WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent fire, do not cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. [. . . ] · If the system is playing back a tape at the preset time, the system will switch to the timer, but the timer recording will not be made. Timer The c REC indicator lights up. Adjust the volume* for listening to the radio when it is activated by the timer. * This is not affect the recording volume: it only adjusts the volume for when the radio turns on at the preset time. Press TAPE nN, if you want to switch the direction. repeatedly to select "g" to record on one side or "h" to record on both sides. 7 8 9 10 Press PLAY MODE/DIRECTION 11 Press ?/1 to turn off the system. 15GB Display Turning off the display -- Power Saving Mode The clock display can be turned off to minimize the amount of power consumed during standby (Power Saving Mode). Press DISPLAY. Viewing information about the disc in the display You can check the playing time and remaining time of the current track or that of the disc. Checking the remaining time (CD) Press DISPLAY repeatedly. To cancel Power Saving Mode Press DISPLAY. Tips Each time you press the button, the display changes cyclically as follows: During playback Current track number and elapsed playing time of the track*1 t Current track number and remaining time of the track*2 t Remaining time of the current disc t Clock display (for six seconds) *1"­ ­ ­. ­ ­" appears when the total playing time of the · The ?/1 indicator lights up even in the Power Saving Mode. · The timer continues to operate in Power Saving Mode. Adjusting the brightness of the display's backlight You can change the brightness of the display's backlight. program exceeds 100 minutes, when the program contains 31 tracks or more, or when a disc with 31 tracks or more is played in Shuffle Play mode. *2"­ ­ ­. ­ ­" appears when a track is played whose 1 2 Press DISPLAY repeatedly until "DIMMER X" appears. Press . /> repeatedly. number is 31 or over. In the stop mode Total playing time y Clock display (for six seconds) Each time you press the button, the brightness changes cyclically as follows: DIMMER 0 t DIMMER 1 t DIMMER 2 16GB Optional Components Hooking up optional components To enhance your system, you can connect optional components. Refer to the operating instructions provided with each component. Optional Components From the audio output jacks of an optional analog component Optional analog component A MD IN jacks Use audio cords (not supplied) to connect an optional analog component (MD deck, etc. ) to these jacks. You can then listen to the sound from the component. Recording audio from a connected component 1 Connect audio cords. 2 Start recording manually. See "Recording on a tape manually" on page 12. Listening to audio from a connected component 1 Connect audio cords. See "Hooking up optional components" on page 17. 2 Press MD. Start playing the connected component. 17GB Troubleshooting Problems and remedies Should you encounter a problem with your system, do the following: 1 Make sure the power cord and speaker cords are correctly and firmly connected. The clock setting/radio presetting/timer is canceled. · The power cord is disconnected or a power failure occurs longer than half a day. Redo the following: ­ "Setting the clock" (page 5) ­ "Presetting radio stations" (page 8) If you have set the timer, also redo "Waking up to music" (page 14) and "Timer recording radio programs" (page 15). · Make sure the headphones are not connected. · Insert only the stripped portion of the speaker cord into the SPEAKERS terminal. Inserting the vinyl portion of the speaker cord will obstruct the speaker connections (page 4). Sound comes from one channel, or unbalanced left and right volume. · Check the speaker connection and speaker placement. · Check that the speaker's + and ­ terminals are connected correctly. · A TV or VCR is placed too close to the stereo system. Move the stereo system away from the TV or VCR. · Connect the system to a different wall outlet. · Install a noise filter (commercially available) to the power line. · Set the clock correctly (page 5). [. . . ] Do not use such discs. Note on CD-R/CD-RW playback Discs recorded on CD-R/CD-RW drives may not be played back because of scratches, dirt, recording condition or the drive's characteristics. Besides, the discs, which are not yet finalized at the end of recording, cannot be played back. Music discs encoded with copyright protection technologies This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. [. . . ]