User manual SONY CMT-HPR90

[. . . ] WARNING 2-668-124-11(1) Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed. Micro HI-FI Component System Operating Instructions Owner's Record The model and serial numbers are located on the rear of the unit. Record these numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. [. . . ] 3 After "STANDBY" stops flashing, press Discs that this system CANNOT play · CD-ROM · CD-R/CD-RW other than those recorded in music CD format or "ATRAC" format and MP3 format conforming to ISO9660 Level 1/Level 2, Joliet or multisession · CD-R/CD-RW recorded in multisession that have not ended by "closing the session" · CD-R/CD-RW of poor recording quality, CD-R/CDRW that have scratches or are dirty, or CD-R/CD-RW recorded with an incompatible recording device · CD-R/CD-RW which is finalized incorrectly · Discs containing files other than MPEG 1 Audio Layer3 (MP3) files · Discs of non-standard shape (for example, heart, square, star) · Discs that have adhesive tape, paper, or sticker attached to them · Rental or used discs with attached seals where the glue extends beyond the seal · Discs that have labels printed using ink that feels tacky when touched FM stereo, FM/AM superheterodyne tuner FM tuner section: Tuning range: 87. 5 ­ 108. 0 MHz Antenna: FM lead antenna Antenna terminals: 75 ohms unbalanced Intermediate frequency: 10. 7 MHz AM tuner section: Tuning range: 530 ­ 1, 710 kHz (with 10 kHz tuning interval) 531 ­ 1, 710 kHz (with 9 kHz tuning interval) Antenna: AM loop antenna Antenna terminals: External antenna terminal Intermediate frequency: 450 kHz 3 Press DISC SKIP to select a disc. 4 Press / repeatedly or turn the jog dial on the unit until the desired track number appears. When programming "ATRAC" files or MP3 files, press +/­ (select folder) repeatedly or turn the jog dial on the unit to select the desired folder, and then select the desired file. Current disc Selected track or file number Total playing time of program (including selected track or file) Play Timer: You can wake up to CD or tuner at a preset time. Use buttons on the remote to control the Play Timer. Make sure you have set the clock. 1 Prepare the sound source. Prepare the sound source, and then press VOLUME +/­ to adjust the volume. To start from a specific CD track, "ATRAC" file or MP3 file, create your own CD program. Immediately unplug the power cord, and check the following item. · If your system has a voltage selector, is the voltage selector set to the correct voltage?· Are you using only the supplied speakers?· Is anything blocking the ventilation holes on the rear of the system?After the STANDBY indicator stops flashing, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. (power) while holding ENTER . "CD POWER" and "OFF" appear. With CD player power turned off, disc access time is increased. To turn on CD player power, repeat the procedure until "CD POWER" and "ON" appear. Speaker Speaker system: 2-way, bass-reflex type Speaker units Woofer: 13 cm dia. , cone type Tweeter: 4 cm dia. , cone type Nominal impedance: 4 ohms Dimensions (w/h/d): Approx. 174 × 280 × 258 mm Mass: Approx. 2. 6 kg net per speaker To reset the system to factory settings General Power requirements: 120 V AC, 60 Hz Power consumption: 45 watts Dimensions (w/h/d) (excl. 180 × 280 × 360 mm Mass (excl. speakers): 3. 9 kg Supplied accessories: Remote Commander (1)/R6 (Size AA) batteries (2)/AM loop antenna (1)/FM lead antenna (1) US and foreign patents licensed from Dolby Laboratories. Design and specifications are subject to change without notice. If the system still does not operate properly, reset the system to factory settings. You cannot reset the system to factory settings in Power Saving Mode. Use buttons on the unit to reset the unit to its factory default settings. General The display starts flashing as soon as you plug in the power cord even though you have not turned on the system. 1 Disconnect and reconnect the power cord, and then turn on the system. 2 Press PLAY MODE/TUNING MODE , 2 Press CLOCK/TIMER SET . 3 Press / repeatedly to select "PLAY Loaded disc SET" then press ENTER . [. . . ] At high volume, speaker vibration may cause the sound to skip. To change the setting Start over from step 1. Tip The Play Timer setting remains as long as the setting is not canceled manually. Presetting radio stations You can preset your favorite radio stations and tune them in instantly by selecting the corresponding preset number. Use buttons on the remote to preset stations. Display examples Display indicates Play does not start from the first track. 2 (two) 5 (five) 6 (six) 8 (eight) 0 (zero) A B D G H K M O Q R S Z !@ ^ · Return to Normal Play by pressing PLAY MODE repeatedly until both "PGM" and "SHUF" disappear. 1 Tune in the desired station (see "Listening to the radio"). Starting playback takes more time than usual. · The following discs take a longer time to start playback. ­ a disc recorded with a complicated tree structure. [. . . ]