User manual SONY CMT-NEZ50

[. . . ] The model and serial numbers are located on the rear of the unit. Record these numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. ______________ This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Use buttons on the remote to create your own program. You can record on a TYPE I (normal) tape in two ways: FULL : You tried to program more than 26 tracks or files (steps). NO DISC : There is no disc in the player, or you have loaded a disc that cannot be played. nO STEP : All of the programed tracks have been erased. NO TAB : You cannot record because the overwrite protection tab has been removed from the cassette. OVER : You have reached the end of the disc while pressing (fast forward) during playback or pause. PUSH SELECT : You tried to set the clock or timer during timer operation. pUSH STOP : You pressed PLAY MODE during playback. SET CLOCK : You tried to select the timer when the clock is not set. SET TIMER : You tried to select the timer when the Play Timer or Rec Timer is not set. Music discs encoded with copyright protection technologies this product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. 6 Select the sound source or prepare the tape. For Play Timer: Press / repeatedly until the desired sound source appears, and then press ENTER . 1 Make sure the power cord and speaker cords are Inputs AUDIO IN: Sensitivity 250 mV, impedance 47 kilohms Outputs PHONES: Accepts headphones with an impedance of 8 ohms or more SPEAKER: Accepts impedance of 6 to 16 ohms CMT-NEZ33 The following are measured at AC 230 ­ 240 V, 50/60 Hz (Australian model), AC 220 V, 60 Hz (Korean model), AC 120 V, 50/60 Hz (Taiwanese model), AC 120, 220 or 230 ­ 240 V, 50/60 Hz (other models) DIN power output (rated): 14 + 14 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 20 + 20 W (6 ohms at 1 kHz, 10% THD) Inputs AUDIO IN: Sensitivity 250 mV, impedance 47 kilohms Outputs PHONES: Accepts headphones with an impedance of 8 ohms or more SPEAKER: Accepts impedance of 6 to 16 ohms CMT-NEZ30 North-American model: Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz, 10% THD) European model: DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 17 + 17 W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 28 + 28 W The following are measured at AC 220 V, 50/60 Hz (Argentine model), AC 120 V, 60 Hz (Mexican model), AC 120, 220 or 230 ­ 240 V, 50/60 Hz (other models) DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz, 10% THD) Inputs AUDIO IN: Sensitivity 250 mV, impedance 47 kilohms Outputs PHONES: Accepts headphones with an impedance of 8 ohms or more SPEAKER: Accepts impedance of 6 to 16 ohms 2 Find your problem in the checklist below, and Appears while the player is stopped. You can record an entire CD onto a tape. You can record just the portions you like from a sound source, including connected audio components. Use buttons on the unit to control tape recording. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall socket, even if the unit itself has been turned off. ⷠCompletely disconnect the power cord (mains lead) from the wall socket (mains) if it is not going to be used for an extended period of time. When unplugging the unit, always grip the plug. [. . . ] Failure to clean the tape heads can cause degraded sound quality or an inability of the unit to record or play tapes. You can record a preset radio station at a specified time. use buttons on the remote to control the Play Timer and the Rec Timer. MODE repeatedly until "PRESET" appears, and then press +/­ repeatedly to select the desired preset number. [. . . ]