User manual SONY CMT-SPZ90DB

[. . . ] Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) Before unplugging the DAB antenna, make sure the system is turned off to preserve your own DAB settings. ⷠThis tuner does not support data services. This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. [. . . ] you cannot change the setting in Power Saving Mode. Use buttons on the unit to turn off CD player power. Discs that this system CAN play 2 Find your problem in the checklist below, and take While the player is stopped. You can record an entire CD onto a tape. You can record just the portions you like from a sound source, including connected audio components. Use buttons on the unit to control tape recording. Use a demagnetizing cassette (available separately) after every 20 to 30 hours of use. Failure to demagnetize the tape heads can cause an increase in noise, a loss of high frequency sound, and an inability to completely erase tapes. Discs that this system CANNOT play CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to ISO9660 Level 1/Level 2, Joliet or multisession · cD-R/CD-RW recorded in multisession that have not ended by "closing the session" · CD-R/CD-RW of poor recording quality, CD-R/CDRW that have scratches or are dirty, or CD-R/CD-RW recorded with an incompatible recording device · Discs of non-standard shape (for example, heart, square, star) · Discs that have adhesive tape, paper, or sticker attached to them · Rental or used discs with attached seals where the glue extends beyond the seal · Discs that have labels printed using ink that feels tacky when touched DIN power output (rated): 40 + 40 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 50 + 50 W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 50 + 50 W (6 ohms at 1 kHz, 10% THD) Inputs AUDIO IN: Sensitivity 250 mV, impedance 47 kilohms Outputs PHONES: Accepts headphones with an impedance of 8 ohms or more SPEAKER: Accepts impedance of 6 ohms The system turns on 15 seconds before the preset time. When programing MP3 files, press +/­ (select folder) repeatedly to select the desired folder, and then select the desired file. Current disc Selected track or file number Total playing time of program (including selected track or file) 1 Load a recordable tape with the side you want to Load the disc you want to record. When recording a folder from an MP3 disc, press PLAY MODE repeatedly to select " , " and then press +/­ (select folder) repeatedly to select the desired folder. To record only your favorite CD tracks in your desired order, perform steps 2 through 6 of "Creating your own CD program. Press CLOCK/TIMER SELECT , press / repeatedly until "PLAY SEL" or "REC SEL" appears, and then press ENTER . Immediately unplug the power cord, and check the following item. ⷠIf your system has a voltage selector, is the voltage selector set to the correct voltage? ⷠAre you using only the supplied speakers?After the STANDBY indicator stops flashing, reconnect the power cord, and turn on the system. With CD player power turned off, disc access time is increased. To turn on CD player power, repeat the procedure until "CD POWER" and "ON" appear. If the system still does not operate properly, reset the system to factory settings. You cannot reset the system to factory settings in Power Saving Mode. [. . . ] If there is no improvement, move the speakers far away from the TV. Halogenated flame retardants are not used in the certain printed wiring boards. Halogenated flame retardants are not used in cabinets. 4 5 Repeat steps 1 through 4 to store other stations. [. . . ]