User manual SONY CMT-V10IP

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Turn the jog dial upward or downward then press it for the tracks or files you want to program in the order you want. Audio CD Playing order Programed track ATRAC CD/ MP3 CD* Playing order Programed file *You can also select another group pressing + or ­. 24 4 Press CD u to start Program Play. On the remote 1 Press FUNCTION repeatedly until "CD" appears on the display. 2 Press MODE repeatedly until "PGM" appears on the display. 3 Press the number buttons or . /m, M/ + or ­ > for the tracks or files (or press for the groups) you want to program in the order you want. 4 Press u. Playing tracks repeatedly (Repeat play) You can play tracks repeatedly in normal play mode and other play modes you want. FUNCTION REPEAT The CD Player To cancel Program Play Stop playing first. Then press MODE/DIR repeatedly until "PGM" disappears from the display. To check the order of tracks before play Press the jog dial after step 2. Every time you press the jog dial, the track or file number appears in the programed order. To change the current program Press STOP x once after step 2. Then create a new program following the programing procedure. Tips · You can play the same program again, since the program is saved until you open the CD tray. · You can record your own program. After you have created the program, insert a blank tape into the tape compartment then start recording (see page 15). 1 2 Press FUNCTION repeatedly until "CD" appears on the display when the player is not in CD mode. (Example: To tune in a preset station 12, press >10 and 1 first , and then press 2. ) 28 The Audio Emphasis Selecting the audio emphasis You can adjust the audio emphasis of the sound you are listening to. Reinforcing the bass sound Press MEGA BASS on the remote to display "MEGABASS". MEGA BASS Selecting the sound characteristic Press SOUND repeatedly to select the audio emphasis you want. The Audio Emphasis SOUND To return to normal sound, press the button again to make "MEGABASS" disappear from the display. Choose To get powerful, clean sounds, emphasizing low and high range audio light, bright sounds emphasizing high and middle range audio percussive sounds, emphasizing bass audio the presence of vocals, stressing middle range audio the whole dynamic range for music such as classical music 29 The Timer Setting the clock "­ ­:­ ­" indicator appears on the display until you set the clock. Jog dial (PUSH ENTER/ MEMORY) CLOCK Note If you disconnect the AC power cord, the clock display may return to "­ ­:­ ­". Tip The time display system of this player is the 12hour system. AM 12:00 = midnight PM 12:00 = noon To check the present time Press CLOCK to display the clock, and press it again to go back to the previous display. Before you begin, hook up the system (see pages 35 - 36). 1 Press and hold CLOCK until the hour digit flashes. 2 Set the clock. 1 Turn the jog dial to set the hour and press it. 2 Turn the jog dial to set the minutes. 3 Press the jog dial. The clock starts from 00 seconds. 30 Waking up to music You can wake up to music or a radio program at a preset time. Make sure you have set the clock (see "Setting the clock" on page 30). Jog dial (PUSH ENTER/ MEMORY) STANDBY 4 Turn the jog dial to select the music source you want to play ("CD", "TAPE", "TUNER" or "LINE"), and press the jog dial to enter the selection. TIMER 5 Set the timer to the hour and the minutes you want the music to go on. 1 Turn the jog dial to set the hour and press it. The Timer 2 Turn the jog dial to set the minutes and press it. 6 Before you begin, make sure the (clock) indicator is not lit on the display. If it is lit, press STANDBY. Set the timer to the hour and the minutes you want the music to go off. (Do as step 5. ) Turn the jog dial to set the volume you want. 7 1 Prepare the music source you want to play. Source CD TAPE TUNER LINE Do this Insert a CD. Turn on the equipment connected to LINE IN. 8 2 3 Press TIMER. [. . . ] · Make sure the safety tab of the tape in the tape compartment is in place. If not, "No Tab" will be displayed. The audio is weak/The audio quality is poor. · Clean the heads, pinch rollers and capstans (See page 43). [. . . ]