User manual SONY CMT-V11IP

[. . . ] 4-462-381-11 (1) Location of Controls Unit (Top) Remote Operations Playing a CD/MP3 disc 1 Select the CD function. Press CD FUNCTION  on the remote or press FUNCTION  on the unit repeatedly.  Compatibility with all MP3 encoding/writing software, recording device, and recording media cannot be guaranteed. Incompatible MP3 discs may produce noise or interrupted audio or may not play at all. * This include folders that have no MP3 or other files. The number of folders that the system can recognize may be less than actual number of folders, depending on the folder structure. To tune in to a preset radio station If you registered a radio station to a preset number 1 to 6, the radio station will be tuned in by just pressing the TUNER MEMORY NUMBER (1 to 6)  when the system function is set to FM or AM. [. . . ]  If the sound source for a Play Timer is set to an FM/AM station tuned in using auto scanning or manual scanning, when you change the radio station after setting the Play Timer, radio station tuning for the Play Timer will also changed.  If the sound source for a Play Timer is set to an FM/AM station with a registered preset number, the radio station tuning for the Play Timer is fixed at what you set for it. Even if you change the radio station after setting the Play Timer, the radio station setting for the Play Timer will not change.  You are using an unsupported USB device. Check the information on the websites about compatible USB devices.  Turn off the system and reconnect the USB device, then turn on the system.  The music data itself contains noise, or the sound is distorted. Noise may have entered during the transferring process. Delete the file, and try transferring again.  The bit rate used when encoding audio files was low. Send audio files with higher bit rate to the USB device.  Find a location and an orientation that provide good reception, and then set up the antenna again.  Bundle the antenna cables using commercially available cord clips, for example, and adjust the cable lengths. To reset the system to factory settings If the system still does not operate properly, reset the system to factory settings. Use buttons on the unit to reset the system to its factory default settings. 1 Disconnect and reconnect the power cord, and then turn on the system.  CD-ROM  CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to ISO9660 Level 1/Level 2, Joliet  CD-R/CD-RW of poor recording quality, CD-R/CD‑RW that have scratches or are dirty, or CD‑R/CD-RW recorded with an incompatible recording device  CD-R/CD-RW which is finalized incorrectly  Discs containing files other than MPEG 1 Audio Layer3 (MP3) files  Discs of non-standard shape (for example, heart, square, star)  Discs that have adhesive tape, paper, or sticker attached to them  Rental or used discs with attached seals where the glue extends beyond the seal  Discs that have labels printed using ink that feels tacky when touched CD player section System: Compact disc and digital audio system Laser Diode Properties Emission Duration: Continuous Laser Output*: Less than 44. 6 µW * This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. Frequency response: 20 Hz  20 kHz Signal-to-noise ratio: More than 80 dB Dynamic range: More than 80 dB Tuner section Antenna: FM lead antenna AM loop antenna FM tuner section Tuning range: 87. 5 MHz  108. 0 MHz (50 kHz step) AM tuner section Tuning range: European model: 531 kHz  1602 kHz (9 kHz step) Latin American and Australian models: 530 kHz  1710 kHz (10 kHz step) 531 kHz  1710 kHz (9 kHz step) Other models: 531 kHz  1602 kHz (9 kHz step) 530 kHz  1610 kHz (10 kHz step) MP3 disc/USB device Notes for the iPod/iPhone user To control the iPod/iPhone To Pause playback Press  /  (or   on the unit). To fast-forward or fast-rewind, hold down the button.  rack or file name (“ ”) t  rtist name (“ ”) a  lbum name (“ a ”)  Make sure the iPod/iPhone is not playing when using the Play Timer.  The Play Timer may not be activated depending on the status of the connected iPod/iPhone. “READING” is displayed for an extended time, or it takes a long time before playback starts.  The reading process can take a long time in the following cases:  There are many folders or files on the USB device  The file structure is extremely complex  The memory capacity is excessive  The internal memory is fragmented 2 Press and hold   and /  on the unit until “RESET” appears in the display. All user-configured settings, such as preset radio stations, timer, and the clock, are deleted. Notes on discs USB section The system offers the following display modes. Display mode Power Saving mode1) When the system is off The display is turned off to conserve power. The timer and clock continue to operate. The clock is displayed. Tip The Play Timer setting remains in effect as long as the setting is not canceled manually and clock setting is completed. To turn off the Automatic Standby function Pause Select a track or chapter of audiobook/ podcast Find a point in a track or chapter of audiobook/ podcast Choose the selected item Scroll up/down the iPod menus Return to the previous menu Clock 1) 2) 2) Troubleshooting 1 Make sure the power cord is firmly connected. 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. Erroneous display. Hold down /  during playback, and release the button at the desired point. /  . You cannot set the clock in Power Saving mode. The clock display automatically turns to Power Saving mode after 8 seconds. / . RETURN /  . To use the system as a battery charger You can use the system as a battery charger for an iPod/ iPhone while the system is on. [. . . ]  Make sure the iPod/iPhone is playing music.  Make sure the iPod/iPhone is updated with the latest software. If not, update the iPod/iPhone before using with the system.  Adjust the volume. 3 Select the AUDIO IN function. Press AUDIO IN FUNCTION  on the remote or press FUNCTION  on the unit repeatedly. 1 Prepare the sound source. Prepare the sound source, and then press VOLUME +/  to adjust the volume. [. . . ]