User manual SONY CMT-ED2

[. . . ] 3-867-342-13(1) Micro HiFi Component System Operating Instructions Owner's Record The model and serial numbers are located on the rear of the system. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Serial No. CMT-ED2/ED2U ©1999 by Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. [. . . ] The following table describes the two repeat modes. To repeat All the tracks on the CD Only the currently playing track* Press CD REPEAT repeatedly until "REPEAT" appears. CD REPEAT repeatedly until "REPEAT 1" appears. Tip Each time you press DISPLAY while the CD is stopped, the display changes as follows: Clock display Y Current source display and total playing time * This function does not work during Shuffle Play or Program Play. To cancel Repeat Play Press CD REPEAT repeatedly until "REPEAT" and "REPEAT 1" disappear. 20 Playing CD tracks in random order -- Shuffle Play You can use this function to playback all the tracks on a CD in random order. To cancel Shuffle Play Press PLAY MODE repeatedly until "SHUFFLE" disappears. Tips · You can also start Shuffle Play during Normal Play by selecting "SHUFFLE". · To skip a track, press L. 1 ?/1 Note You cannot go back to the preceding track by pressing l. + ­ The CD Player n x N 3 L 2 1 2 3 Press FUNCTION on the unit repeatedly until "CD" appears. Press PLAY MODE repeatedly until "SHUFFLE" appears. ";" appears while the next track is being selected, and all the tracks play in random order. 21 Playing CD tracks in a favorite order ­­ Program Play You can make a program of up to 24 tracks on a CD in any order that you want. 3 Press l or L repeatedly until the desired track number appears. 3 243 Total playing time Selected track number 1 ?/1 + ­ 4 Press ENTER. The selected track is programmed. The number of the selection just programmed appears, followed by the total playing time of the program. n x N 5 6 2 s To program additional tracks, repeat steps 3 and 4. The tracks play in the order that they were programmed. 3 6 To cancel Program Play Press PLAY MODE repeatedly until "PROGRAM" disappears. 4 1 2 Press FUNCTION on the unit repeatedly until "CD" appears. Press PLAY MODE repeatedly until "PROGRAM" appears. To Add a track to the end of the program Erase the entire program Do this Do steps 3 and 4 with Program Play stopped. Press s with Program Play stopped. Tips · The program you made remains in the system's memory until you turn off the system or remove the CD. After the program finishes, press CD H to play the program again. · When the total playing time of the programmed tracks exceeds 100 minutes, "- - . · If you try to program more than 24 tracks, "FULL" appears in the display. 22 The Tape Deck Recording to a tape manually Do the procedure below to manually record from any source to a tape. For example, tracks from a CD, the radio, or from any of the connected components. This lets you record just the songs that you want from a CD. 1 2 3 4 5 6 To Insert a recordable tape. Press FUNCTION repeatedly until the source you want to record from appears. Press z REC on the remote. The tape stands by for recording. "REC" appears. 2 ?/1 x Press DIR MODE on the remote to select "g" to record on one side of the tape or "j" to record on both sides. Press X. Recording starts on the side of the tape facing towards you. The Tape Deck CD Player/The Tape Deck + ­ n x N . m X M> Z Start playing the source you want to record from. Press x. Press x again to stop playing the CD. * X. Stop recording Pause recording 1 5 * When recording from a CD only Tips · To record with the Dolby NR system on, press DOLBY NR on the remote before step 5. · When recording from a CD, CD synchro recording starts (see "Recording from a CD to a tape" on page 14). 4 DOLBY NR 3 23 Recording your favorite CD tracks to a tape -- Program Edit With Program Edit function, you can select only the CD tracks that you want using the Program Play function, then record the programmed tracks to a tape using the CD Synchro Recording function. 1 2 3 4 5 Place a CD. Press FUNCTION on the unit repeatedly until "CD" appears. [. . . ] · The record protect tab has been removed from the cassette (see page 31). · The tape has come to the end. Resetting the system 1 Disconnect the power cord from the wall outlet. 2 Press ?/1 down and connect the power cord to the wall outlet again. The system is reset to the factory settings. [. . . ]