User manual SONY CRU-40SG12

[. . . ] Refer to them whenever you call upon your Sony dealer regarding this product. Model No. _____________ Serial No. ______________ The socket-outlet shall be installed near the equipment and shall be easily accessible. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by rotating the equipment off and on, the user is encouraged to try to correct the interference using one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. [. . . ] The battery icon on the screen changes to the battery charging icon ( ). It takes about four hours for your CLIÉ handheld to be fully charged for the first time. Subsequent charges, if your CLIÉ handheld is charged frequently, will require less time. To the wall outlet Insert your CLIÉ handheld at an angle to the cradle and lay it back to fit into place. When you place your CLIÉ handheld on the cradle, the LED indicator of your CLIÉ handheld turn on, and charging starts. When charging is completed The LED indicator of your CLIÉ handheld turns off. When you remove your CLIÉ handheld from the cradle, the battery charging icon changes to the battery icon ( ). Note If the battery in your CLIÉ handheld is fully discharged, all data stored on the DRAM (memory) is lost. Performing another HotSync® operation once the battery is recharged can restore information saved from the last HotSync operation. 26 Step 2: Turning on your Sony CLIÉ Handheld for the first time Opening the display panel To operate on your CLIÉ handheld, set your CLIÉ handheld to the "opened style" or the "turned style. " Here, the steps guide you to the "turned style. " 1 Open the display panel until it clicks into place. The "carrying style" changes to the "opened style. " Chapter 2 b 2 Rotate the display clockwise until it clicks into place, then fold it over the keyboard. Setting up your Sony CLIÉ Handheld ­ Basics b Your CLIÉ handheld is now in the "turned style. " 27 Step 2: Turning on your Sony CLIÉ Handheld for the first time Making the initial setting The first time you turn on your CLIÉ handheld, setup instructions appear on the screen. Follow the on-screen instructions to configure the initial settings, including caliberating the digitizer and setting the current time, date, and year. (This configuration is necessary for operation of the CLIÉ handheld). 1 Press the POWER button. Your CLIÉ handheld turns on, and the Welcome screen appears. After a while, the Setup screen appears. Press the POWER button. b 2 Take out the Stylus. You can use the stylus to tap or drag on the screen to open applications, choose options or menu commands, and select text or move objects, just as you do with a mouse on your computer. Note Always use the point of the stylus for tapping or making strokes on the handheld screen. Never use a real pen, pencil, or other sharp object to write on the screen. 28 3 Press lightly on the screen with the stylus. This action is called "tapping. " The digitizer calibration screen appears. Calibration aligns the internal circuitry of the handheld with its touch-sensitive screen so your CLIÉ handheld can detect the task you want to perform when you tap an element on the screen. Chapter 2 Setting up your Sony CLIÉ Handheld ­ Basics 4 Tap anywhere on the screen. The following screen is displayed. Continued on next page 29 Step 2: Turning on your Sony CLIÉ Handheld for the first time 5 Following the on-screen instruction, tap the center of the displayed mark. Note If the digitizer is not configured correctly, the scroll bar may not operate properly, "tapping" may not work as expected, or other problems may occur. If this happens, please re-configure the digitizer manually. · The Palm Desktop for CLIÉ software supplied with this CLIÉ handheld (CRU-40SG12V/U, CRU-40SG12/U) does not support the Expense application. · Do not simply copy the Palm Desktop for CLIÉ software files to your computer's hard disk. You must use the installer and follow the procedures described in this section to place the files in their proper locations and to decompress the files. · To introduce the CLIÉ data of your old CLIÉ handheld into the new one, see "Using data of another Sony CLIÉ Handheld" in the Operating Instructions manual. Setting up your Sony CLIÉ Handheld ­ Basics 1 Exit all applications running on Windows®. You should quit all applications that automatically run at startup, such as fax communication software, anti-virus tools, screensavers, and the Microsoft® Office Shortcut Bar. 2 Insert the Installation CD-ROM into the CD-ROM drive of your computer. The installation launcher window appears. Continued on next page 35 Step 4: Installing the PalmTM Desktop for CLIÉ software on your computer 3 Click Install Palm Desktop for CLIÉ. The setup program starts and the Welcome screen is displayed. 4 Click Next. The Palm Desktop for CLIÉ 4. 0. 1 software installation begins. Follow the on-screen instructions until the following dialog box appears. 5 Select the software you will use to synchronize your CLIÉ handheld with your computer. If you select "Synchronize with Palm Desktop for CLIÉ, " Intellisync Lite will not be installed. If you select "Synchronize with Microsoft Outlook or Lotus Organizer, " Palm Desktop and Intellisync Lite will be installed. 36 6 Click Next. The Setup Type window is displayed. Chapter 2 Setting up your Sony CLIÉ Handheld ­ Basics 7 Select the setup type (Typical or Custom) and the destination folder. If you wish to synchronize PEG-S300 or PEG-N710C with your CLIÉ handheld (CRU-40SG12V/U, CRU-40SG12/U), follow the steps below: 1 Select Custom for the setup type, and click Next. 2 On the select components screen, make sure that USB Switcher is selected. 3 Follow the on-screen instructions until setup is complete. When you follow the on-screen instructions, the Create User Account screen is displayed. 8 9 Fill in the user name in the Create User Account screen. Click Next. The Install Tool dialog box closes, then the Mail Setup dialog box appears. 10 Set up Mail. Follow the on-screen instructions until Mail setup is complete. Continued on next page 37 Step 4: Installing the PalmTM Desktop for CLIÉ software on your computer 11 Fill in the customer registration following the instructions shown on the screen. You must have Internet access for the online customer registration. You can take advantage of Sony's commitment to quality customer support and nine-month extension of the limited warranty (for a total of 12months from the original date of purchase) when you register your CLIÉ handheld. 12 Click Finish. Note Make sure you perform a HotSync operation before installing any thirdparty applications. [. . . ] Perform a HotSync operation. The application(s) you selected in step 6 will be installed on your CLIÉ handheld. See page 40 (Step 6: Performing a HotSync® operation for the first time) for details on performing a local HotSync operation. 60 To access the Install Tool dialog box Do either of the following to display the Install Tool dialog box immediately: · Click Start on the taskbar, point to Programs (All Programs in Windows® XP), Sony Handheld, and then click Install Tool. · Double-click any file with a PRC, or PDB file extension. To install applications to the Memory Stick media You can install applications to the Memory Stick media by performing one of the following: · Use the MS Import/Export applications to install applications directly on an inserted Memory Stick media (See the Add-on Applications Guide for details). · Install applications through the Palm Desktop for CLIÉ software by clicking Change Destination after performing step 6 on page 60. [. . . ]