User manual SONY CSDTD53

[. . . ] 6 Carts and stands - When placed or mounted on a stand or cart, the unit should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit or cart to overturn or fall. 7 Condensation - Moisture may form on the CD pickup lens when: - The unit is moved from a cold spot to a warm spot - The heating system has just been turned on - The unit is used in a very humid room - The unit is cooled by an air conditioner When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again. [. . . ] 5 When not in use - Unplug the AC power cord from the AC outlet or remove all the batteries if the unit will not be used for several months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the power is turned off. OPE/BATT The OPE/BATT indicator lights up while the power is on. Using on AC house current Connect the AC cord as illustrated below. to the AC inlet of the unit supplied AC cord to an AC outlet (AC 120 V, 60 Hz) Maintenance Clean the unit only as recommended in the Operating Instructions. CAUTION Use only the supplied AC cord. Use with other cords may result in the risk of fire. En Damage Requiring Service Have the units serviced by a qualified service technician if: - The AC power cord or plug has been damaged - Foreign objects or liquid have got inside the unit - The unit has been exposed to rain or water - The unit does not seem to operate normally - The unit exhibits a marked change in performance - The unit has been dropped, or the cabinet has been damaged DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF. Using on batteries Open the lid of the battery compartment on the rear and insert eight R14 (size C) batteries, not supplied, with the 0 and 9 marks correctly aligned. To switch from AC power supply to battery power supply, disconnect the AC cord from the AC inlet. R14 (C) When to replace the batteries The OPE/BATT indicator becomes dim, the tape speed slows down, volume decreases, or sound is distorted during operation. Notes on batteries · Do not mix different types of batteries or old batteries with new ones. · When the unit is not to be used for a long period, remove the batteries to prevent needless battery wear. · Never recharge the batteries, apply heat to them or take them apart. If liquid leaks from the batteries, wipe thoroughly to remove. ENGLISH 3 RADIO/BAND, POWER 6STANDBY A SKIP/SEARCH PLAY/PAUSE/ PRESET + \ - TUNE REPEAT FM MODE /OSC SLEEP STOP/MEMORY A 1 TUNER OPERATION FM MODE/OSC - If an FM stereo broadcast contains noise, press the button so that is displayed. Noise is reduced, although reception is monaural. To restore stereo reception, press the button again. - If a high-pitched sound is heard during AM recording, press the button repeatedly until the noise is reduced. Its position can be checked by "·" being on or off the display. Press RADIO/BAND repeatedly to select the desired band. FM AM The power is turned on and the previously tuned station is received. 2 Press r, t (TUNE -, +) to select a station. During FM stereo reception, is displayed. To change the AM tuning interval After listening, press POWER 6STANDBY to turn the power off. · The unit may not play a CD-R/RW disc that is recorded on personal computers or some kinds of CD-R/RW recorders because of differences in recording platforms. · Do not attach any seal or label to either side (the recordable side or the labeled side) of a CD-R/RW disc. · Do not load an unrecorded CD-R/RW disc. It will take over 30 seconds to read the disc. The disc may be damaged if you try to open the disc compartment while reading the disc. Total number of tracks and total playing time are displayed. It will take about 15 seconds when loading a CD-RW disc. 3 Press e PLAY/PAUSE/PRESET to start play. The number of the track being played and elapsed playing time are displayed. s STOP/MEMORY ­ Stops play. r, t SKIP/SEARCH ­ Searches for a particular point during playback. Keep r or t pressed and then release it. ­ Skips to the beginning of a track. REPEAT ­ Repeats a single track or all tracks. [ 1 : A single track is played repeatedly. [. . . ] Press QSOUND and the QSOUND indicator lights up. · At higher volumes, turning QSOUND on may cause sound distortion. Specified time While the sleep timer works, the dot keeps flashing. To check the time remaining until the power is turned off Repeat step 1 shown above. The remaining time is displayed for 4 seconds. To cancel the sleep timer Display the remaining time and press r or t repeatedly until OFF is displayed. NOTE If the unit is turned off during tape playback, x on the deck will not be released. [. . . ]