User manual SONY CSM-100BS

[. . . ] CONSOLIDATED STORAGE MANAGEMENT SYSTEM CSM-200BF/200BS CSM-100BF/100BS CSM-60BF/60BS CSM-200D CSM-200C · · CSM OPERATION MANUAL 1st Edition (Revised 1) [Japanese/English] · · · c 1 2 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2(J) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4(J) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5(J) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] IN and OUT indicators lit: The bar code on a cartridge is being read. In some operating modes, a cartridge may be pulled in before the indicators are lit. IN and OUT indicators blinking: No barcode label is attached to the cartridge or the label cannot be read. 3 Function buttons The functions of these buttons are set using software. 4 OPEN buttons To load or remove a cartridge via the ports, press the buttons to open the doors. When the buttons are pressed, they light and remain lit until the ports are closed. Depending on the operating condition of the system, some time may be required until the doors open. When an error is generated, the lamps of the buttons flash. Power switch Turn the power of the unit on and off. 12(E) Preparations Installation A technician specially trained for CSM system and PetaSite-series equipment must perform setting and wiring the units, and making system environment settings. Ethernet Interface Ports of the PCU The PCU has two Ethernet interface ports: one for the local network to control the PetaSite system, and another for the network for the other system other than PetaSite. PCU Rear Panel Connection Example This is an example of the system to completely back up 2 terabytes of data in eight hours. Application server HP-UX 500 GB Application server SUN Solaris 500 GB Ethernet interface port to control the other system Ethernet interface port to control the PetaSite system Network NAS server NetApp filer 1 TB Port for the PetaSite system network Be sure to connect the units for this system only to the network to be used to control the PetaSite system. Caution Fibre Channel switch For your safety, connect the LAN port only to a network with surge protection. Port for the system other than PetaSite For setting this port, ask the network administrator for the IP address. PetaSite S200 series (PetaSite Control Unit built-in) For settings, see "Setting the host name and IP address of the PCU" on page 14(E). PetaServe/PetaBack software for CSM 13(E) Preparations Settings Initial settings of the DZC-PSC2 The DZC-PSC2 PetaSite Control Software has been installed on the PCU, and the required initial settings have been made at the factory. Depending on the environment, the initial settings may be changed. For changing the initial settings, refer to on-line help for the DZC-PSC2. To refer to on-line help, click on the Help button of the MMT window of the DZC-PSC2. Setting the host name and IP address of the PCU The PCU has several files keyed with the host name and IP address. Before starting operation of the CSM System, set the host name and IP address, and reflect them in these files. Set the host name and IP address following the procedure below, then the settings will be reflected in the files. Note The host name and IP address can not be changed after starting operation of the CSM System. If you need to change them, contact to Sony support center. Starting the DZC-PSC2 Follow the procedures below to start the DZC-PSC2. 1 2 3 4 5 6 7 8 9 Type "root" in the Username box to log in, and open the Terminal window. Click on the PetaApp icon on the desktop. Click on the Utility icon to open the Utility window. Select "Administrator" from the Mode list box at the right top on the Utility window. Type "sony" (initial password) in the Password box. Click on the Network tab of the Utility window. Read the notice, then click on Network Configurator at the bottom of the window to start Network Configurator. Type the new host name in the HostName column, and the new domain name in the Domain column in the Names window. Add the host name and IP address relationships required for operating the new host and the IP address in the Hosts window. 1 2 3 Turn the PCU on. Type "sonypsc" in the Username box, and "psc2002" (initial password) in the Password box of the Login window. [. . . ] Sony Corporation has specially designed PetaApp Linux for the PetaSite Control Unit based on the RedHat Linux 8. 0 ftp version. In the window, messages related to RedHat Corporation may appear, but RedHat Corporation has no relation to the PCU. Never contact RedHat Corporation. Initial Settings of Device Settings at the factory are as shown below. PCU Hostname/IP Address (eth0) : petalocal. petadomain 10. 0. 0. 100/255. 255. 255. 0 (eth1) : petahost. petadomain 192. 168. 20. 3/255. 255. 255. 0 Initial account/password: root, sony2002 : sonypsc, psc2002 GPL/LGPL PetaApp Linux includes GPL/LGPL software. Therefore, you have the right to obtain, modify and redistribute the source code for PetaApp Linux. [. . . ]