User manual SONY CXLEM30

[. . . ] CD Stereo System XR-EM30 U Owner's record For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty. (Lot No. ) OPERATING INSTRUCTIONS En (English) MANUAL DE INSTRUCCIONES E (Español) MODE D'EMPLOI F (Français) For assistance and information (United States and Puerto Rico) 8C-CL6-903-01 020220BCK-H-BF WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION IMPORTANT SAFETY INSTRUCTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN En Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. [. . . ] 2 Press PRESET + , - on the remote control repeatedly. With each press, the station with the succeeding or preceding preset number is tuned in. You can tune in the desired preset station directly by pressing the numbered buttons on the remote control. - To select preset number 11, press +10 and 1. - To select preset number 15, press +10 and 5. To clear a preset station 1 Tune in the station by preset tuning. 2 Press s, then press SET on the remote control within 6 seconds. Preset station numbers in the band which are higher than the cleared number decrease by one. En f, g Manual tuning 1 Press TUNER/AUX/BAND (TUNER/BAND on the remote control) repeatedly to select a band. 2 Press f or g repeatedly to tune in a station. "TUNE" is displayed when a station is tuned in. "1" is displayed for FM stereo reception. To search for a station automatically (Auto search) Hold down f or g. The unit searches for a station and stops at reception. To stop the search manually, press f or g. ·Auto search may not stop at stations with weak signals. Preset tuning Preset up to 32 of your favourite stations and tune them in directly. Presetting stations 1 Tune in the desired station. 2 Press SET on the remote control to store the station. The preset number, beginning from "1" flashes on the display. 3 Repeat steps 1 and 2 to preset other stations. The next station will not be stored if a total of 32 preset stations have already been stored. ("FULL" is displayed. ) ·If power is interrupted for more than approximately 12 hours, all settings stored in memory after purchase need to be reset. 10 SOUND ADJUSTMENTS Adjustments To switch to monaural FM reception Hold down SHIFT and press TUNER MODE on the remote control so that "MONO" is displayed. To cancel, repeat the above so that "STEREO" is displayed. TONE VOLUME Tip: When FM stereo reception is poor, switching to monaural reduces noise. To switch the AM tuning interval The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the tuning interval. Hold down TUNER/AUX/BAND and press POWER on the main unit. VOLUME +, TONE En Tip: When the AM tuning interval is changed, all preset stations are cleared. Volume Turn VOLUME (press VOLUME +, - on the remote control). Adjust from 0 (minimum) to 30 and MAX (maximum). Bass and treble 1 Press TONE repeatedly to display "BAS" or "TRE". "BAS" : Adjusts the bass level "TRE" : Adjusts the treble level Tip: Volume level setting is retained during power-off standby. If the unit is turned off with the volume set to 17 or higher, it is automatically turned down to 16 the next time the unit is turned on. 2 Within 6 seconds, turn VOLUME (press VOLUME +, - on the remote control). Each level can be adjusted from "­2" to "+5". ·If the sound becomes distorted, lower the level. 11 TAPE PLAYBACK Notes on cassettes TUNER MODE c f, g REC/ REC PAUSE REC MUTE FUNCTION ·Use of 120-minute or longer tapes is not recommended since they are extremely thin and easily deformed or damaged. ·Wind up any slack in the tape with a pencil or similar tool before use. [. . . ] The unit shut off suddenly ·Possibly a short circuit in the speaker terminals. Disconnect the AC power cord from the AC outlet and reconnect the speaker cords correctly. Erroneous display ·Reset the unit. (See "Resetting the unit" on this page. ) Poor radio reception ·Check antenna connection. [. . . ]