User manual SONY D830K

[. . . ] BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE, OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF. reserves the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein is governed by the terms of a separate user license agreement. This product contains software owned by Sony and licensed by third parties. [. . . ] Connection for an audio cable (supplied). Connection for a video cable adapter (supplied) or an S-video cable (optional). Connection for a digital audio or optical device. Connection for a TV coaxial cable (supplied). Connection for the supplied stereo speakers. Connection for a modem (supplied) cable to the telephone wall jack. 10 VAIO MX Computer System Reference Manual I/O Connectors The following section identifies the various I/O connectors. Keyboard and Mouse Ports The keyboard and mouse ports are physically identical and have the same pinout. They are standard 6-pin PS/2® compatible female ports. 2 3 1 4 5 6 USB Ports The USB ports are standard 4-pin USB ports. One USB port is located at the front, and another at the rear of the system. Ethernet Port The Ethernet port at the rear of the system is used to connect to a 10Base-T/100Base-TX Ethernet network. Ethernet Identifying Components Serial Port 11 The serial port is a standard 9-pin DB-9 male port. 6 1 9 5 Printer/Parallel Port The printer/parallel port is a standard 25-pin DB-25 female port. 25 13 14 1 12 VAIO MX Computer System Reference Manual Monitor Port The monitor port is a standard 15-pin female high-density VGA-type port located on the AGP plug-in card. 10 15 5 11 6 1 DVI-D Port The DVI-D port is a 24-pin DVI-D port that can be attached to a Sony XGA LCD panel (PCVA-15XD2), which uses a DVI-D connector cable (sold separately). The DVI-D port is located on the AGP plug-in card. You can physically connect both a VGA and an LCD monitor at the same time. However, you cannot use both monitors at the same time. The following message appears at the bottom of the screen. Press <F2> for setup. 3 Press F2. Each menu presents options for modifying the system configuration. Use the left and right arrow keys to select a menu from the menu bar. Use the up and down arrow keys to select items within a menu. Once an item is highlighted, use the plus/minus (+/-) keys to modify a setting. If an item has a triangle ( ) to its left, this indicates that a sub-menu of options is available. If a submenu contains items with a triangle, there is another layer of options from which to select. 4 5 Once you select an option, press ESC to back out of each menu until you reach the top level, where the menu bar appears. To exit the BIOS setup utility, press ESC from any top-level screen and follow the prompts. Configuring Your System 19 Changing the Display's Power Management Settings A display that has power management capability is designed to operate on reduced power or shut itself off after the system has been idle for a specified period of time. 1 From the Start menu, point to Settings, click Control Panel, then click Display. The Power Options Properties dialog box opens, with the Power Schemes tab displayed. 20 VAIO MX Computer System Reference Manual 2 Select the power scheme that is most appropriate for the way you use your computer. To change a power scheme, change the settings for Turn off monitor, and Turn off hard disks, System standby, and System hibernates. [. . . ] Access to the CMOS Setup Utility depends on which passwords were previously set, as indicated next. If you set these passwords. . . User password only Supervisor password only . . . the following passwords are required: User password is required at bootup. Supervisor password is required by most setup options. Supervisor password is required by most setup options. Both passwords Miscellaneous Technical Information 69 Beep Code Error Messages During a normal bootup, a single short beep signifies that the system is OK. [. . . ]