User manual SONY HANDYCAM DCR-SX45/L HANDYCAM HANDBOOK

[. . . ] 2. 2* Audio recording system (HDV) Rotary heads, MPEG-1 Audio Layer-2, Quantization: 16 bits Fs48kHz (stereo) transfer rate: 384 kbps Audio recording system (DVCAM (DV)) Rotary heads, PCM system Quantization: 12 bits Fs32kHz (channel 1/2 stereo), Quantization: 16 bits Fs48kHz (channel 1/2 stereo) Video signal PAL color, CCIR standards 1080/50i specification Usable cassette Mini DV cassette with the mark printed or Mini DVCAM cassette with the mark printed Tape speed (HDV) Approx. 18. 831 mm/s Recording/playback time (HDV) 63 min (using a PHDVM-63DM cassette) Recording/playback time (DVCAM) 41 min (using a PHDVM-63DM cassette) Recording/playback time (DV SP) 63 min (using a PHDVM-63DM cassette) Fast forward/rewind time Approx. 2 min 40 s (using a PHDVM63DM cassette and rechargeable battery pack) Approx. 1 min 45 s (using a PHDVM63DM cassette and AC Adaptor/ Charger) Viewfinder Electric viewfinder (color, black and white) Picture 1. 1 cm (0. 45 type, aspect ratio 16:9) Total dot number 1 226 880 (approx. [. . . ] 6-2-14 HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U 6-95 3-8. Tracking Check 1) Play back the tracking standard (XH2-1A1) (Ref. Take the amplitude (A) in this mode as the 100% waveform amplitude. Confirm that the difference between the minimum (E min) and the maximum (E max) is less than 30%. (When taking the amplitude (A) in the CUE or REV mode as 100%) CUE/REV mode 2. CUE/REV Check 1) Play back the tracking standard (XH2-1A1) (Ref. Confirm that the pitches between the peaks of the RF waveform are equally spaced. Also confirm that the RF waveform amplitude at entrance side (B) and exit side (C) is 50% or more respectively, when taking the amplitude (A) in the CUE or REV mode as 100%. Confirm that the pitches between the peaks of the RF waveform are equally spaced. Also confirm that the RF waveform amplitude at entrance side (B) and exit side (C) is 50% or more respectively. A=100% B C A=100% 400 sec FWD mode B = 50% or more C = 50% or more E max E min Fig. Rise-up Check 1) Play back the tracking standard (XH2-1A1) (Ref. 6-3-1 HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U 6-97 3-1-4. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking tape (XH2-1A1) SW/OL standard (XH2-3) Audio operation check (XH5-3 (NTSC), XH5-3P (PAL)) System operation check (XH5-5 (NTSC), XH5-5P (PAL)) Use Tape path adjustment Switching position adjustment Audio system adjustment Operation check Fig. 6-3-2 shows the 75% color bar signals recorded on the alignment tape for Audio Operation Check. Note: Measure with video terminal (Terminated at 75 ) For NTSC model White (100%) Yellow Cyan Green Magenta Red Blue White (75%) Yellow Green Cyan Red Blue Black 0. 714 V 1V (75%) 0. 286 V 0. 286 V Q I Q White (100%) I Black Horizontal sync signal Color bar signal waveform Color bar pattern For PAL model Yellow Cyan Green White (100%) White Cyan 0. 3 V 0. 3 V Burst signal (100%) Horizontal sync signal Color bar signal waveform Color bar pattern Fig. 6-3-2 Color bar signal of alignment tapes 3-1-5. Output Level and Impedance A/V Remote Connector 10-pin connector When A/V connecting cable is connected Video signal: 1 Vp-p, 75 (ohms) Luminance signal: 1 Vp-p, 75 (ohms) Chrominance signal: 0. 286 Vp-p (burst signal), 75 (ohms) (NTSC) Chrominance signal: 0. 3 Vp-p (burst signal), 75 (ohms) (PAL) When Component A/V connecting cable is connected Y: 1 Vp-p, 75 (ohms), PB/PR, CB/CR: +/350mV, 75 (ohms) Audio signal: -10 dBu (at load impedance 47 k (kilohms)), Output impedance with less than 2. 2 k (kilohms) (0 dBu=0. 775 Vrms) HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U 6-98 Red 1V Magenta Yellow Green 0. 7 V Magenta Red Blue Blue Burst signal Magenta White 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENTS D1 (decimal) 00001 to 65535 65536 to 131071 131072 to196607 D2 (decimal) D1 D1 - 65536 D1 - 131072 H1 (hexadecimal) (Service model code) FE FE FE FE FE FE FE FE FE FE FE FE FE FE FE FE 1. Initialization of EEPROM Data If the EEPROM data is erased due to some reason, perform "1-2. INITIALIZATION OF EVR DATA ", of "6-1. Input of Serial No. " if the data on page 13 has been cleared and original node unique ID No. [. . . ] Description X-2320-852-1 HOLDER (24000) ASSY, BT 5-1-14. Description X-2320-852-2 HOLDER (24000) ASSY, BT [ 5-2. ELECTRICAL PARTS LIST Page JK-376 BOARD Ref. Description - : Points changed portion ! [. . . ]