User manual SONY DD1EX

[. . . ] BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE, OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF. SONY CANNOT WARRANT THAT THE FUNCTIONS DESCRIBED IN THIS GUIDE WILL BE UNINTERRUPTED OR ERROR-FREE. SONY ALSO ASSUMES NO RESPONSIBILITY, AND SHALL NOT BE LIABLE FOR ANY DAMAGES TO, OR VIRUSES THAT MAY INFECT, YOUR COMPUTER EQUIPMENT, OR OTHER PROPERTY ON ACCOUNT OF YOUR ACCESS TO, USE OF, OR BROWSING IN ANY DESCRIBED WEB SITE, OR YOUR DOWNLOADING OF ANY MATERIALS, DATA, TEXT, IMAGES, VIDEO, OR AUDIO FROM ANY DESCRIBED WEB SITE. WEB SITE INFORMATION IS OBTAINED FROM VARIOUS SOURCES AND MAY BE INACCURATE. [. . . ] 1. 0 Vrms (typical), 10 Kohm impedance. Telephone and Modem Line Jacks The telephone and modem line jacks are physically identical and have identical connections. They are standard RJ-11 female phone jacks. However, the modem line jack is for connecting a telephone line that comes from the wall to the computer, and the telephone jack is for connecting the telephone to a computer. Telephone Modem Line Line Identifying Components i. LINK S400 (IEEE 1394) Ports 13 The 6-pin i. LINK® port on the back panel of the system can supply power from the computer to an i. LINK device if the device also has a 6-pin i. LINK port. The 6-pin port supplies 10 V to 12 V and a maximum power of 6 watts. i. LINK is a trademark of Sony used only to designate that a product contains an IEEE 1394 connection. The i. LINK connection may vary, depending on the software applications, operating system and compatible i. LINK devices. All products with an i. LINK connection may not communicate with each other. Refer to the documentation that came with your compatible i. LINK device for information on operating conditions and proper connections. Before connecting compatible i. LINK devices to your system, such as an optical disk or hard disk drive, confirm their operating system compatibility and required operating conditions. The 4-pin i. LINK port at the bottom of the front panel does not supply power to an i. LINK device. 6-pin i. LINK port (IEEE 1394) 4-pin i. LINK port (IEEE 1394) On back of system Behind lower front panel Ethernet Port The Ethernet port on the back panel of the system is used to connect to a 10BASE-T/100BASE-TX Ethernet network. Ethernet On back of system 14 VAIO Computer System Reference Manual Expansion Slots There are five expansion slots; however, four slot covers are visible from the back panel (see "System Board" on page 47). Expansion Slot No. 5 4 3 2 1 Description Not available for expansion. Available for expansion when the CNR slot is not occupied. Only one slot can be occupied at a time. The UPS tab enables you to select and configure an Uninterruptible Power Supply (UPS) device for your system. A UPS device is an optional accessory not supplied with your system. 9 Select the settings most appropriate for your system and click OK. For more information about configuring a UPS device, refer to the Microsoft® Windows® XP operating system Help. 22 VAIO Computer System Reference Manual Chapter 3 Upgrading and Maintaining Components This chapter describes upgrade and maintenance procedures. System configuration may vary, depending on the model purchased. Your computer may not include all of the hardware features shown in the illustrations of this section. ! Before opening the system unit, save and close all open files, exit all open applications, turn off the power to all attached peripheral devices, shut down the computer, and unplug the power cord. 23 24 VAIO Computer System Reference Manual Removing the Cover Removing the cover 1 2 3 4 Shut down your computer and turn off all peripheral devices, such as your printer. Unplug your computer and disconnect any peripheral devices. Position the system unit so that the back panel is facing towards you. Unscrew the three cover release screws located on the edges of the back panel and set aside. Removing the release screws 5 When the screws are removed, the cover is released. Slide the cover towards the back of the unit to remove it. Upgrading and Maintaining Components 25 Removing the cover ! If you remove the cover immediately after you shut down your computer, the components may be too hot to touch. Wait until the internal parts of the system unit cool down before you attempt to remove the cover. Replacing the cover 1 2 3 Carefully align the cover to the chassis frame. The cover should align evenly against the chassis. Slide the cover firmly onto the unit, sliding it forward until the cover snaps into place. [. . . ] User password only Supervisor password only . . . the following passwords are required: User password is required at bootup. Supervisor password is required by most setup options. Supervisor password is required by most setup options. Both passwords Miscellaneous Technical Information 61 Beep Code Error Messages During a normal bootup, a single short beep signifies that the system is OK. The number of beeps indicates the specific error that occurred. [. . . ]