User manual SONY DF200

[. . . ] 3-241-441-11 (1) FM/AM Portable CD Player Operating Instructions About the area code The area code of the location in which you purchased the CD player is shown on upper left of the bar code label on the package. For accessories supplied with your CD player, check the area code of your model and see "Accessories (supplied/optional). " "WALKMAN" is a trademark of Sony Corporation. D-F200 © 2002 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To prevent fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. And don't place lighted candles on the apparatus. [. . . ] When the station is preset successfully, the beep sounds and "PRESET" stops flashing in the display. FM: AM: 4 5 6 Using the radio After 2 seconds, "PRESET" starts flashing again and the CD player enters the PRESET MEMORY standby mode. 7 Repeat steps 4 to 6 when you preset the stations in the same band. When you preset the stations in the different band, repeat steps 2 to 6 after "PRESET" stops flashing. To exit the PRESET MEMORY standby mode When the radio is turned on, you can exit the PRESET MEMORY standby mode using one of the following procedures. Preset stations, however, will remain stored in the CD player's memory. · Hold down MEMORY until "PRESET" stops flashing. · Do not press any button for 10 seconds. The CD player enters the CD playing mode. The radio turns off. (Continued) 11 Presetting radio stations To cancel all preset stations 1 Disconnect the power source (alkaline batteries or AC power adaptor). 2 While you press and hold down MEMORY, insert alkaline batteries or connect the AC power adaptor again. The indications in the display keep flashing until all preset stations are cleared, then stop flashing and disappear from the display. Playing preset radio stations You can tune in the station easily by pressing PRESET + or ­ button. 1 2 Press RADIO ON·BAND to select the band. Press PRESET + or ­ to tune in a stored station. Changing the tuning interval When using the CD player abroad, change the AM tuning interval, if necessary. Set the STEP switch (in the battery compartment) to "9 kHz" or "10 kHz" using a pointed material. 9 kHz area: Asia and Europe 10 kHz area: the U. S. A. , Canada and South America Notes · The interval will not change until you once turn off the radio and then turn it on again. · After changing the tuning interval, you need to preset radio stations again. 12 B Available features To maximize the skip protection performance (ESP MAX) The typical ESP (Electronic Shock Protection) function minimizes skipping by using a buffer memory that stores music data and plays it back in the event of a shock. Connect the power source while pressing x on the CD player. To turn on the beep sound Remove the power source and then connect the power source without pressing x . Available features 15 B Connecting your CD player Connecting a stereo system You can listen to CDs through a stereo system and record CDs on a cassette tape. For details, see the instruction manual that comes with the connected device. Be sure to turn off all connected devices before making connections. Notes · Before you play a CD, turn down the volume of the connected device to avoid damaging the connected speakers. · We recommend that you use the AC power adaptor (not supplied) for recording. If you use the dry batteries as a power source, they may become completely depleted during recording. · Adjust the volume properly on the CD player and connected device so that the sound will not be distorted or noisy. to i Adjust the volume. Connecting cord Left (white) Right (red) Stereo system, cassette recorder, radio cassette recorder, etc. 16 B Connecting to a power source You can use the following power sources: · LR6 (size AA) alkaline batteries (see "Playing a CD") · AC power adaptor For the battery life, see "Specifications. " Notes · The indicator sections of roughly shows the remaining battery power. One section does not always indicate one-fourth of the battery power. · Depending on operating conditions, the indicator sections of may increase or decrease. Using the dry batteries For inserting procedure, see "Playing a CD. " To remove the batteries Remove the batteries as illustrated below. To attach the battery compartment lid If the battery compartment lid is detached by an accidental drop, excessive force, etc. , attach it as illustrated below. (rear) When to replace the batteries You can check the remaining power of the batteries in the display. [. . . ] (page 6) c Moisture condensation has occurred. Leave the CD player aside for several hours until the moisture evaporates. c Close the lid of the battery compartment firmly. (page 6) c Make sure the batteries are inserted correctly. [. . . ]