User manual SONY DHC-MDX10

[. . . ] Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. US and foreign patents licensed from Dolby Laboratories. This appliance is classified as a CLASS 1 LASER product. [. . . ] The TOC is updated when you eject the MD or press ?/1 to turn off the system. Do not pull out the power cord before updating the TOC (while "TOC" is lit) or while updating the TOC (while "TOC" is flashing) to ensure a complete editing. 37 Labeling an MD -- Name Function You can create titles for your recorded MDs and tracks as follows. 2 Press NAME EDIT/SELECT. The text input screen appears, and the cursor flashes. Cursor During recording If "TEXT" flashes in the display during recording a CD, you can record the track titles on the MD (see page 26). After recording Use Name Function on this page. You can input a total of approximately 1700 characters for the disc title and track titles on a single MD. 3 Press NAME EDIT/SELECT to select the desired type of character. Each time you press the button, the display changes as follows: Selected AB* (Upper cases) t Selected ab (Lower cases) t Selected 12 (Numbers) t Selected AB (Upper cases) t . . . * Press number 1 repeatedly to display the following symbols. In addition, when the symbols above appear in the display, press ­ or + repeatedly to display the following symbols. &+<>_=";#$%@ ` 2, 3 4 TCURSOR CLEAR CURSORt 4 + Enter a character. If you've selected uppercase or lowercase letters 1 Press the corresponding letter/number button repeatedly until the character to be entered flashes. Or, press the button once and press ­ or + repeatedly. The flashing character is entered and the cursor shifts to the right. ­ 1 6 If you've selected numbers 1 Press FUNCTION repeatedly to switch the function to MD. To label a track, press ­ or + repeatedly until the desired track number appears. Press the corresponding number button. The number is entered and the cursor shifts to the right. 38 5 Repeat steps 3 and 4 to enter the rest of the name. To change a character Press TCURSOR or CURSORt repeatedly until the character to be changed flashes, press CLEAR to erase the character, then repeat steps 3 and 4. Copying a disc or track title You can copy a labeled disc or track title to use it as a title of another track or the disc title within a disc. 2 Press ­ or + repeatedly until "Name?" appears, then press ENTER/YES. To erase all the titles, press ­ or + repeatedly until "Nm All Ers?" appears, then press ENTER/YES twice after performing 1 and 2. Erasing a single track (Track Erase Function) You can erase a track simply by selecting its track number. When you erase a track, the total number of tracks on the MD decreases by one and all the tracks following the erased one are renumbered. Eg. : Erasing track 2. Track number Original tracks Erase track 2 1 2 3 4 To cancel erasing Press MENU/NO. To return to the condition before labeling or erasing You can return to the original condition immediately after labeling or erasing a title (see page 48). A 1 B 2 C 3 D After ERASE A C D When erasing multiple tracks, you should proceed in order from high to low track number to prevent the renumbering of tracks that have not been erased yet. 2 3, 4 1 3, 5 3, 4 40 1 2 3 4 Press FUNCTION repeatedly to switch the function to MD. Press MENU/NO to display "Edit Menu". Press ­ or + repeatedly until "Tr Erase?" appears, then press ENTER/YES. or > repeatedly until the desired track number appears. Erasing all tracks (All Erase Function) You can erase the disc title, all recorded tracks and their titles at once. 2 3 1 3, 4 3 The MD Deck -- Editing 5 Press ENTER/YES. "Complete!" appears for a few seconds and the selected track and title are erased. 1 2 3 Press FUNCTION repeatedly to switch the function to MD. Press MENU/NO to display "Edit Menu". Press ­ or + repeatedly until "All Erase?" appears, then press ENTER/ YES. "All Erase??" appears. To cancel erasing Press MENU/NO. Note "Erase???" appears when the track was recorded or edited on another deck and is protected. To erase the track, press ENTER/YES while "Erase???" appears. 4 Press ENTER/YES again. "Complete!" appears for a few seconds and the disc title, all recorded tracks and their titles are erased. To cancel erasing Press MENU/NO. continued 41 Erasing recordings (continued) 1 2 Press FUNCTION repeatedly to switch the function to MD. While playing an MD, press X at the starting point of the portion to be erased (point A). The MD pauses. Erasing a portion of a track (A-B Erase Function) You can specify a portion within a track and erase the portion with ease. [. . . ] SPEAKER: accepts impedance of 6 to 16 ohms. FM tuner section Tuning range Tourist model: European model: Other models: Antenna Antenna terminals Intermediate frequency 76. 0 ­ 108. 0 MHz (50 kHz step) 87. 5 ­ 108. 0 MHz (50 kHz step) 87. 5 ­ 108. 0 MHz (100 kHz step) FM lead antenna 75 ohms unbalanced 10. 7 MHz AM tuner section Tuning range European model: Other models: 531 ­ 1, 602 kHz (with the interval set at 9 kHz) 531 ­ 1, 602 kHz (with the interval set at 9 kHz) 530 ­ 1, 710 kHz (with the interval set at 10 kHz) AM loop antenna External antenna terminals 450 kHz Antenna Intermediate frequency 70 Speaker (SS-CMD595) Speaker system Speaker units Woofer: Tweeter: Nominal impedance 2-way, bass-reflex type 12 cm dia. , cone type 2. 8 cm dia. , balanced drive type 6 ohms Parts descriptions for the remote You can use the supplied remote to control the system. Note You cannot perform the following operations with the remote; -- Removing discs -- Selecting the recording mode -- CD-MD Synchro Recording General Power requirements U. S. A. and Canadian models: 120 V AC, 60 Hz Australian model: 220 ­ 240 V AC, 50/60 Hz Chinese model: 220 V AC, 50/60 Hz European model: 230 V AC, 50/60 Hz Other models: 110 ­ 120 V or 220 ­ 240 V AC, 50/60 Hz Power consumption U. S. A. and Canadian models: 60 watts during normal operation Other models: 70 watts during normal operation Dimensions (w/h/d) incl. [. . . ]