User manual SONY DNWA25WS

[. . . ] DIGITAL VIDEOCASSETTE RECORDER DNW-A25WS DNW-A25WSP INSTALLATION MANUAL 1st Edition Serial No. WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! [. . . ] If the above adaptor is used, power on the VTRs and load cassettes in turn allowing for an inrush current. While the unit is battery-operated, the remaining battery capacity is displayed on the sub menu indicator. When the battery is nearly dead, the WARNING indicator on the side of the LCD monitor will blink. For details, refer to the operation manual supplied with the unit. Connection example (when operating two VTRs) Ni-cd battery BP-90A + Battery adaptor DC-L90 AC adaptor AC-DN2A/DN2B AC adaptor AC-DN2A/DN2B Lithium-ion battery BP-L90A/L60A DC OUT Battery terminal DNW-A25WS/A25WSP Rear View DC IN (DC cable) AC adaptor AC-550 Ni-cd battery BP-90A + Battery adaptor DC-210 1-2 DNW-A25WS/A25WSP 1-5. Installation Space c To avoid an injury, do not install the unit on rickety table. Ventilation and Installation Space for Servicing . Do not block an exhaust section and an air vent (rear panel). In order to make a unit with good ventilation, ensure sufficient clearance around the unit. In order to ensure a workspace, more than 20 cm behind the unit is required. Outside Dimensions 89 145 461 443 R217 0d 12 150 157 331 349 210 230 Unit : mm DNW-A25WS/A25WSP 1-3 1-6. Connectors/Cables Connection made with the connector panels during installation or service, should be made with the connectors or complete cable assemblies specified in the following list, or equivalent parts. Panel indication VIDEO REF IN VIDEO INPUT VIDEO OUTPUT TC IN TC OUT SDI IN SDI OUT AUDIO INPUT Connection connector (Sony P/N) Plug, BNC (1-564-742-11) Connection cable (Sony P/N) RG-59B/U cable Plug, BNC (1-564-742-11) BNC coaxial cable (1-791-456-11: supplied with BKNW-225) or BELDEN 8281 cable (Maximum cable length: 200 m) ­­­­­­­ ­­­­­­­ DC power cord (1-551-577-00:supplied with AC-550/ 550CE) ­­­­­­­ 9P remote control cable (1-783-089-12: supplied with BKNW-225) or RCC-5G(5 m)/10G(10 m)/30G(30 m) ­­­­­­­ ­­­­­­­ XLR 3P, MALE (1-508-084-00) AUDIO OUTPUT XLR 3P, FEMALE (1-508-083-00) MONITOR OUTPUT DC IN DC OUT REMOTE XLR 4P, FEMALE (1-508-362-00) Plug 4P MALE (1-566-425-11) Plug 9P MALE (1-560-651-00) Shell, Junction 9P (1-561-749-00) Plug 6P MALE (1-560-078-00) JM-60 stereo phone plug (Separately available) AUX HEADPHONES 1-4 DNW-A25WS/A25WSP 1-7. Signal Inputs and Outputs 1 2 3 4 567 8 AUDIO INPUT OFF 75Z OFF +48V _60 0 ON +4dBu OFF +48V _60 0 ON +4dBu ON VIDEO OFF 75Z ON REF. IN INPUT OUTPUT 1 CH-1 CH-2 2(SUPER) REMOTE AUDIO OUTPUT 1/3 2/4 R DC-IN MONITOR OUTPUT L SDI IN DC OUT TC IN 1 SDI OUT 2 TC OUT AUX < Connector panel > 9 !/ !- != ![ !] !\ Communications Connectors 6 ![ REMOTE AUX D-SUB 9P connector x 1 (RS-422A interface) Remote control 6-pin connector x 1 Input Connectors 1 AUDIO INPUT CH-1/CH-2 XLR 3-pin x2 Analog audio 2 channels _60 dBu, 0 dBu, +4 dBu selectable, high impedance, balanced VIDEO REF. IN BNC x2 (In loop through connection, with 75 Z termination switch) External reference video signal (Black burst or composite sync) 40 IRE/0. 3 Vp-p, 75 Z, negative sync BNC x2 (In loop through connection, with 75 Z termination switch) Analog composite video 1. 0 Vp-p, 75 Z, negative sync BNC x1 Component digital (270 Mbit/s) SMPTE 259M/ITU-R BT. 656 BNC x1 Time code 0. 5 to 18. 0 Vp-p, 10 kZ, unbalanced XLR 4-pin x1 DC +11 to 17 V 5-pin terminal x1 Lithium-ion battery interface 2 3 !8 !\ VIDEO INPUT SDI IN TC IN DC IN BATTERY IN (on battery sub panel) DNW-A25WS/A25WSP 1-5 1-7. Signal Inputs and Outputs Output Connectors 4 5 9 VIDEO OUTPUT 1 VIDEO OUTPUT 2 AUDIO OUTPUT 1/3, 2/4 BNC x1 Analog composite video 1. 0 Vp-p, 75 Z, negative sync BNC x1 (Character superimpose enabled) Analog composite video 1. 0 Vp-p, 75 Z, negative sync XLR 3-pin x2 Analog audio 2 channels (CH-1/CH-2 or CH-3/CH-4 selectable by sub menu) +4 dBm (standard) (600 Z load), low impedance, balanced XLR 3-pin x2 Analog audio channel (AUDIO OUTPUT enabled by selecting sub menu) +4 dBm (standard) (600 Z load), low impedance, balanced BNC x2 Component digital (270 Mbit/s) SMPTE 259M/ITU-R BT. 656 BNCx1 Time code 1. 0 Vp-p ± 3 dB (75 Z load), unbalanced 4-pin connector x1 (for BVR-3) DC +12 V (+11 to 17 V), 0. 5 A (max) JM-60 stereo phone jack Analog audio up to _20 dBu adjustable (8 Z load), unbalanced !/ MONITOR OUTPUT R/L != !] 7 SDI OUT TC OUT DC OUT HEADPHONES (at the front) 6 REMOTE (9P Female) Pin No. 1 2 3 4 5 6 7 8 9 Signal GND RM TX (_) RM RX (_) GND PRIORITY GND RM TX (+) RM RX (+) GND 9 6 5 1 (External View) !\ DC IN (4P Male) Pin No. RE-150 Board A 1 B C D E F G 2 3 SL1 4 RE-150 board 5 RE-150 Board (A Side) n For removing/reattaching the boards, refer to the maintenance manual, volume 1. SL1 Description Selects how the power is derived when the battery and external power supply are used simultaneously Open: Always derived from the external power supply Short: Normally derived from the external power supply When an input voltage is 10. 5 V or below, automatically selects the battery Factory setting Open DNW-A25WS/A25WSP 1-9 1-9. Setup Extended Menu The extended menus of the setup menu are usually not accessible. To display them, set the DIP switch S201 bit-1 on the SY-259A board to ON. (As for the S201 bit-2, this setting allows the maintenance mode to activate. ) m . For removing/reattaching the prug-in boards, refer to Section 1-11. [. . . ] To open the control panel, insert a screwdriver into the rectangular hole and unhook as shown in the figure. Turn the manual eject knob (red) counterclockwise while pushing down it. When the tape is starting to slack, turn the capstan cap counterclockwise to take up the tape to the T reel. Repeat steps 3 and 4 until the cassette compartment is opened. [. . . ]