User manual SONY DR-270DP

[. . . ] To reduce the risk of fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. And do not place lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not place objects filled with liquids, such as vases, on the apparatus. Connect the AC power adaptor to an easily accessible AC outlet. [. . . ] All pairing information is deleted. Procedures of pairing 1 Place the Bluetooth device within 1 m (3 ft) of this unit. 2 Press and hold the PAIRING button for 2 seconds or more to standby for pairing. The indicator (blue) and indicator (red) flash together and the unit enters into pairing mode. Note If pairing is not established within about 5 minutes, pairing mode will be cancelled and this unit will turn off. In this case, start over from step 1. 12 US 3 Perform pairing procedure on the Bluetooth device to detect this unit. The list of detected devices appears on the display of the Bluetooth device. This unit is displayed as "DR-270DP. " If "DR-270DP" is not displayed, repeat from step 1. Notes · For details, refer to the operating instructions supplied with the Bluetooth device. · When pairing with a Bluetooth device that cannot display a list of detected devices or that has no display, you may pair the device by setting both this unit and the Bluetooth device to pairing mode. . . . Connecting ­­ B R­ B R R­ ­ ­­ ­­ Connected HFP/HSP or A2DP B (standby for receiving audio signal) ­­­­­­­­­ ­­­­­­­ ­­­­­­­­ ­­­­­­­ . . . ­­­­­­­­ ­­­­­­­ ­ ­ ­ ­ ­ . . . ­ ­ ­ . . . HFP/HSP and A2DP B (standby for receiving audio signal) R­ B R­ Listening Music Listening during standby B for telephone call R­ Incoming call B R­ B R­ Phone Talking ­ ­ ­ ­ . . . ­ ­ ­ . . . Calling while B playing back music R­ 16 US OPERATING THE UNIT Listening to music VOL + When not calling with this unit, do not make the last connected Bluetooth device ready for HFP or HSP connection. To make or receive a call while playing back music, see page 23. POWER button VOL ­ 2 Make the Bluetooth connection (A2DP) from a Bluetooth device to this unit. Refer to the operating instructions supplied with the Bluetooth device on how to operate it. Check the following before operating the unit. ­ The Bluetooth device is turned on. ­ Pairing of this unit and the Bluetooth device is complete. Refer to the manual supplied with your mobile phone on operating details. ­ When not communicating, you can call using the voice-dial function by pressing the multi function button. ­ You can call the last dialed number by pressing the multi function button for about 2 seconds. To adjust the volume Push the jog switch up or down to adjust the volume. Tips · You cannot adjust the volume when not communicating. · Volume for calling and listening to music can be adjusted independently. Even if you change the volume while playing back the music, the volume of a call does not change. To terminate a call You can end a call by pressing the multi function button on the unit. To receive a call When an incoming call arrives, a ring tone will be heard from the unit. Continued 21 US To stop use HSP (Headset Profile) Status Standby Multi function button Short Press ­ Long Press Dial*1 1 Terminate Bluetooth connection by the Bluetooth mobile phone. 2 Press and hold the POWER button for about 2 seconds to turn off the power. The indicator (blue) and indicator (red) light up together, and the unit turns off. Outgoing call End outgoing End outgoing call*1 call or change call device to headset*2 Incoming call During call Answer End call*3 ­ Change call device to headset Controlling the Bluetooth mobile phone ­ HFP, HSP The operation of the buttons on this unit varies depending on your mobile phone. HFP (Hands-free Profile) or HSP (Headset Profile) is used for Bluetooth mobile phone. Refer to the operating instructions supplied with your Bluetooth mobile phone on supported Bluetooth profiles or how to operate. HFP (Hands-free Profile) Status Standby Voice Dial active Multi function button Short Press Start Voice Dial*1 Cancel Voice Dial*1 Long Press Last number redial ­ Change call device Reject Change call device *1 Some functions may not be supported depending on the Bluetooth mobile phone. Refer to the operating instructions supplied with your mobile phone. *2 This may vary, depending on the Bluetooth mobile phone. *3 Some functions may not be supported when calling using the Bluetooth mobile phone. Outgoing call End outgoing call Incoming call During call Answer End call 22 US Calling while playing back music The Bluetooth connection using HFP or HSP as well as A2DP is necessary to make a call while playing back music. For example, to make a call using a Bluetooth mobile phone while listening to music on a Bluetooth compatible music player, this unit needs to be connected to the mobile phone using HFP or HSP. Make a Bluetooth connection between this unit and the device in use following the procedures outlined below. 1 Make a Bluetooth connection between this unit and the mobile phone in use with HFP or HSP following the procedures outlined in "Calling" (see page 20). 2 Operate the Bluetooth device (music player or mobile phone) used for playing the music to make a Bluetooth connection to this unit using A2DP. [. . . ] , A2DP Bluetooth connection is not made between this unit and the Bluetooth device. Make an A2DP Bluetooth connection (page 17). , Check that music is being played back by the Bluetooth device. , Check that the volume of the unit is not set too low. [. . . ]