User manual SONY DR-350USB

[. . . ] Do not expose the batteries (battery pack or batteries installed) to excessive heat such as sunshine, fire or the like for a long time. Excessive sound pressure from headphones can cause hearing loss. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. [. . . ] The indicator (blue) and indicator (red) flash together and the unit enters into pairing mode. Note If pairing is not established within about 5 minutes, pairing mode will be cancelled and this unit will turn off. . . . Connectable -- ---- ---- ---- Connecting Connected HFP/HSP or A2DP (standby for receiving audio signal) HFP/HSP and A2DP (standby for receiving audio signal) Listening -- -- -- -- -- -- -- ------------------ -- -------------- ---------------- -------------- . . . ----------. . . ------. . . Music Phone Listening during standby for telephone call Incoming call Talking ---------------- -------------- --------. . . ------. . . Calling while playing back music 1 OPERATING THE UNIT Listening to music VOL + button VOL ­ button POWER button make the last connected Bluetooth device ready for HFP or HSP connection. To make or receive a call while playing back music, see page 22. Make the Bluetooth connection (ADP) from a Bluetooth device to this unit. Refer to the operating instructions supplied with the Bluetooth device on how to operate it. Jog switch This unit supports SCMS-T content protection. You can enjoy music, etc. , from a device such as a mobile phone or portable TV that supports SCMS-T content protection. Check the following before operating the unit. ­ The Bluetooth device is turned on. ­ Pairing of this unit and the Bluetooth device is complete. ­ The Bluetooth device supports the transmitting music function (profile: A2DP*). Start playback on the Bluetooth device. Tip Bluetooth connection of A2DP (Advanced Audio Distribution Profile) can also be operated with the jog switch from this unit to the Bluetooth device except when making a call on this unit. * For details on profiles, see page 6. 1 Press and hold the POWER button for about seconds while the unit is turned off. The indicator (blue) and indicator (red) flash together twice, the unit turns on and then this unit tries to connect to the last Bluetooth mobile phone that was used. Tip This unit will stop trying to connect to the Bluetooth mobile phone after 1 minute. In such a case, press the multi function button to try to connect again. Continued 19 To make a connection with the last connected Bluetooth device by operating this unit 1 Press the multi function button. The indicator (blue) and indicator (red) start flashing at the same time, and the unit performs the connection operation for about 5 seconds. ­ ring tone set on the unit ­ ring tone set on the mobile phone ­ ring tone set on the mobile phone only for Bluetooth connection Note If you received a call by pressing the button on the Bluetooth mobile phone, some Bluetooth mobile phones may have handset use priority. In this case, set to talk with the unit by pressing and holding the multi function button for about 2 seconds, or by operating the Bluetooth mobile phone. For details, refer to the manual supplied with your Bluetooth mobile phone. Note When listening to music with this unit, a Bluetooth connection cannot be made with the multi function button. To call 1 Use the buttons on your mobile phone when making a call. If no dialing tone is heard on this unit, press and hold the multi function button for about 2 seconds. To adjust the volume Press the VOL+/­ button. Tips You cannot adjust the volume when not communicating. Volume for calling and listening to music can be adjusted independently. Even if you change the volume while playing back the music, the volume of a call does not change. Tip You can call in the following way, depending on the Bluetooth mobile phone. Refer to the manual supplied with your mobile phone on operating details. ­ When not communicating, you can call using the voice-dial function by pressing the multi function button. [. . . ] Make an A2DP Bluetooth connection (page 16). Check that music is being played back by the Bluetooth device. Check that the volume of the unit is not set too low. Turn up the volume on the connected device if necessary. [. . . ]