User manual SONY DR-BT22

[. . . ] 3-268-834-11(1) Wireless Stereo Headset Operating Instructions DR-BT22 © 2007 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. [. . . ] Even if you change the volume while calling, the volume for music playback does not change. Controlling the audio device ­ AVRCP If the Bluetooth audio device connected with this unit supports AVRCP (Audio Video Remote Control Profile), you can control by using the unit buttons. Refer to the operating instructions supplied with the Bluetooth device on how to operate it. Note Operation of the Bluetooth connecting device by this unit will vary depending on its specification. To stop use 1 Terminate the Bluetooth connection by operating the Bluetooth device. Status: In stop or pause mode Short Press Long Press Nx FF / REW 1 3 2 4 2 Press and hold the POWER button for about 3 seconds. The indicator (blue) and indicator (red) light up together, and the unit turns off. Tip When you finish playing music, the Bluetooth connection may terminate automatically, depending on the Bluetooth device. 1 2 3 4 Starts playback*1 Stop Skip to next/previous Fast-forward/Fast-rewind*2 Short Press Long Press Status: In play mode Nx FF / REW 5 7 6 8 5 6 7 8 Pause*1 Stop Skip to next/previous Fast-forward/Fast-rewind*2 *1 You may need to press the button twice depending on the Bluetooth device. 2 * Some Bluetooth devices may not operate. Note You cannot adjust the volume of the Bluetooth device by the unit volume buttons. 16 Calling VOL + button VOL ­ button Multi function button POWER button When this unit does not connect to a Bluetooth mobile phone automatically You can make a connection by operating Bluetooth mobile phone or by operating this unit to connect the last connected Bluetooth device. Check the following before operating the unit. ­ The Bluetooth function is active on the mobile phone. ­ Pairing of this unit and the Bluetooth mobile phone is complete. A To make a connection by operating Bluetooth mobile phone 1 Make the Bluetooth connection (HFP or HSP*) from the Bluetooth mobile phone to this unit. Refer to the manual supplied with your Bluetooth mobile phone for operation details. The list of recognized devices appears on the display of the Bluetooth mobile phone. This unit is displayed as "DR-BT22. " When you use the Bluetooth mobile phone features both HFP (Hands-free Profile) and HSP (Headset Profile), set to HFP. Note When connecting to a Bluetooth mobile phone which is different from the last connected one, make the connection following the above procedure. * For details on profiles, see page 4. 1 Press and hold the POWER button for about 3 seconds while the unit is turned off. The indicator (blue) and indicator (red) flash together twice, the unit turns on and then this unit tries to connect to the last Bluetooth mobile phone that was used. Note Do not press and hold the POWER button for more than 7 seconds, otherwise pairing mode is entered. Tip This unit will stop trying to connect to the Bluetooth mobile phone after 1 minute. In such a case, press the multi function button to try to connect again. Continued 17 B To make a connection with the last connected Bluetooth device by operating this unit 1 Press the multi function button. The indicator (blue) and indicator (red) start flashing at the same time, and the unit performs the connection operation for about 5 seconds. Note When listening to music with this unit, a Bluetooth connection cannot be made with the multi function button. ­ ring tone set on the unit ­ ring tone set on the mobile phone ­ ring tone set on the mobile phone only for Bluetooth connection Note If you received a call by pressing the button on the Bluetooth mobile phone, some Bluetooth mobile phones may have handset use priority. In this case, set to talk with the unit by pressing and holding the multi function button for about 2 seconds, or by operating the Bluetooth mobile phone. For details, refer to the manual supplied with your Bluetooth mobile phone. To call To adjust the volume Press the VOL + or ­ button. Tips · You cannot adjust the volume when not communicating. · Volume for calling and listening to music can be adjusted independently. Even if you change the volume while playing back the music, the volume of a call does not change. 1 Use the buttons on your mobile phone when making a call. If no dial tone is heard on this unit, press and hold the multi function button for about 2 seconds. Tip You can call in the following way, depending on the Bluetooth mobile phone. Refer to the manual supplied with your mobile phone on operating details. ­ When not communicating, you can call using the voice-dial function by pressing the multi function button. ­ You can call the last dialed number by pressing the multi function button for about 2 seconds. To terminate a call You can end a call by pressing the multi function button on the unit. To stop use 1 Terminate Bluetooth connection by the Bluetooth mobile phone. To receive a call When an incoming call arrives, a ring tone will be heard from the unit. 2 Press and hold the POWER button for about 3 seconds to turn off the power. The indicator (blue) and indicator (red) light up together, and the unit turns off. 1 Press the multi function button on the unit. The ring tone differs in the following ways, depending on your mobile phone. 18 Controlling the Bluetooth mobile phone ­ HFP, HSP The operation of the buttons on this unit varies depending on your mobile phone. HFP (Hands-free Profile) or HSP (Headset Profile) is used for Bluetooth mobile phone. Refer to the operating instructions supplied with your Bluetooth mobile phone on supported Bluetooth profiles or how to operate. HFP (Hands-free Profile) Status Standby Voice Dial active Multi function button Short Press Start Voice Dial*1 Cancel Voice Dial*1 Long Press Last number redial ­ ­ Reject Change call device *1 Some functions may not be supported depending on the Bluetooth mobile phone. Refer to the operating instructions supplied with your mobile phone. 2 * This may vary, depending on the Bluetooth mobile phone. *3 Some functions may not be supported when calling using the Bluetooth mobile phone. Outgoing call End outgoing call Incoming call During call Answer End call HSP (Headset Profile) Status Standby Multi function button Short Press ­ Long Press Dial*1 Outgoing call End outgoing End outgoing call*1 call or change call device to headset*2 Incoming call During call Answer End call*3 ­ Change call device to headset 19 Calling while playing back music The Bluetooth connection using HFP or HSP as well as A2DP is necessary to make a call while playing back music. For example, to make a call using a Bluetooth mobile phone while listening to music on a Bluetooth compatible music player, this unit needs to be connected to the mobile phone using HFP or HSP. Make a Bluetooth connection between this unit and the device in use following the procedures outlined below. 1 Make a Bluetooth connection between this unit and the mobile phone in use with HFP or HSP following the procedures outlined in "Calling" (see page 17). 2 Operate the Bluetooth device (music player or mobile phone) used for playing the music to make a Bluetooth connection to this unit using A2DP. [. . . ] This unit can receive the contents protected by this method. Press and hold the POWER button and Nx again for about 7 seconds to reactivate the SCMS-T content protection method on this unit. The indicator (blue) flashes twice. Terminate A2DP Bluetooth connection by operating the Bluetooth device. While this unit is turned on, press and hold Nx for about 7 seconds to lower the setting of receivable bit rate. [. . . ]