User manual SONY DR-BT22IK

[. . . ] 3-280-122-11 (1) Wireless Stereo Headset Operating Instructions DR-BT22iK © 2007 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. [. . . ] The headset cannot be paired with a Bluetooth receiving device whose passcode is not "0000. " * Passcode may be called "Passkey, " "PIN code, " "PIN number, " or "Password. " When not completed pairing Repeat the procedure from step . To quit "Pairing in process" Press and hold the POWER button of the headset for about 3 seconds to turn off the headset. Note For using the Bluetooth function, it is required that the Bluetooth device on the other side is corresponding with the same profile as the headset. However, even if it is corresponding with the same profile, the function may differ depending on the specification of the Bluetooth device. Continued On Headset Indicators B : Headset indicator (blue) R : Headset indicator (red) Status Pairing Searching Indicator B ­ R ­ B ­ ­ ­ R B ­ ­ R ­ ­ ­ ­ ­ ­ ­­ ­­ ­­ ­ ­ ­­ ­­ ­­ ­ ­ ­ ­ ­­ ­­ ­­ ­ ­ ­­ ­­ ­­ ­. . . ­. . . Connectable Connecting Connecting HFP/HSP or A2DP Connected HFP/HSP and A2DP Listening Music Listening during standby for telephone call Incoming call Talking Calling while playing back music . . . . . . (Standby for receiving audio signal) B ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ R B ­ ­ R ­­­­­­­ ­ ­ ­ ­ ­. . . ­ ­ ­ ­. . . (Standby for receiving audio signal) B ­ ­ ­ ­ ­ ­ ­ ­ ­ R B ­ ­ ­ ­ ­ ­ ­ R ­ B . . . ­ R B ­ ­ ­ ­ ­ ­ ­ ­ ­ R B ­ ­ ­ ­ ­ ­ ­ ­ R ­ ­ ­ ­ . . . ­ ­ ­ . . . Phone ­ ­ ­ ­ . . . ­ ­ ­ . . . Re-pairing the transmitter and the headset 1 2 3 4 Turn on the power of iPod. (Make sure the iPod is in pause mode. ) Connect the transmitter to the iPod (page 16). Place the transmitter and the headset to be paired together within 1 m (3 ft). Press and hold the POWER button of the headset for about 7 seconds or more to enter "Pairing in process" while the headset is turned off. After about 3 seconds, the headset indicator (red) and the headset indicator (blue) will flash twice, but keep pressing the POWER button. 5 Release the POWER button when the headset indicator starts flashing quickly. The headset enters the pairing process. Press and hold the power button of the transmitter for about 7 seconds or more to enter "Pairing in process. " After about 1 second, the transmitter indicator will flash twice, but keep pressing the power button. Continued When first power on the transmitter after initialized, the transmitter will enter "Pairing in process" automatically. Th e pairing information is initialized if you press and hold the power button for 15 seconds. The transmitter indicator lights up for 5 seconds before the initialization starts. Release the button immediately when the transmitter indicator lights up. "Pairing in process" is released after about 5 minutes. If pairing is not established within about 5 minutes, repeat the above procedure from step . iPod backlight may turn on in this 5 minutes. To enter "Pairing in process, " you need to turn off the power of the transmitter first. Notes Calling with headset Preparation for calling (Bluetooth connection) Check the following before operating the headset. ­ The Bluetooth function is active on the mobile phone. ­ Pairing of the headset and the Bluetooth mobile phone is complete. VOL + button VOL ­ button Headset indicator (blue) Headset indicator (red) Multi function button POWER button 1 Press and hold the POWER button for about 3 seconds while the headset is turned off. The headset indicator (blue) and headset indicator (red) flash together twice, the headset turns on and then the headset tries to connect to the last Bluetooth mobile phone that was used. Note Do not press and hold the POWER button for more than 7 seconds, otherwise pairing mode is entered. Tip The headset will stop trying to connect to the Bluetooth mobile phone after 1 minute. In such a case, press the multi function button to try to connect again. When the headset does not connect to a Bluetooth mobile phone automatically You can make a connection by operating Bluetooth mobile phone or by operating the headset to connect the last connected Bluetooth device. Continued make a connection by operating Bluetooth mobile To phone 1 Make the Bluetooth connection (HFP or HSP*) from the Bluetooth mobile phone to the headset. Refer to the manual supplied with your Bluetooth mobile phone for operation details. The list of recognized devices appears on the display of the Bluetooth mobile phone. The headset is displayed as "DR-BT22. " When you use the Bluetooth mobile phone features both HFP (Hands-free Profile) and HSP (Headset Profile), set to HFP. Note When connecting to a Bluetooth mobile phone which is different from the last connected one, make the connection following the above procedure. [. . . ] Turn off the EQ of iPod. The headset is not turned on. No sound Low sound level Cannot change the volume. Distorted sound Continued Symptom Sound break, noise or playback speed change. Cause / Remedy If a device that generates electromagnetic radiation, such as a wireless LAN, other Bluetooth device(s), or a microwave oven is nearby, move away from such sources. Remove any obstacle between the transmitter and the headset or move away from the obstacle. Locate the transmitter and the headset as near as possible. [. . . ]