User manual SONY DR-NXM01CK INSTALLATION & CONNECTIONS

[. . . ] 3-234-493-12(1) For all Models Caution · Do not operate the unit in a way that might divert your attention from driving safely. As a driver, you alone are responsible for safely operating your vehicle in accordance with traffic safety laws at all times. · Do not install the unit where it may obstruct your view through the windshield or your view of your vehicle's indicator displays. · Do not install the unit where it may hinder the function of safety devices such as an air-bag. [. . . ] ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cord clamp* for DRN-XM01H/XM01HK Home cradle (1) XM antenna (1) Remote commander (1) Antenna cord 5 Remove the knob. Cord clamp* Water proof cushion Home stand (1) Audio cord (1) AC power adaptor (1) * · Clean the mounting surface before installing the cord clamp. · Leave the installed cord clamp for 24 hours before installing the cord. Otherwise, the cord clamp may come off because of weak attachment. ;; Trunk lid Rubber packing ; ; ; ; * · Cut the cable guide, if required. · It is difficult to attach the cable guide to a body or window which has fluorine resin coating. For DRN-XM01C/XM01CK For DRN-XM01R For the DRN-XM01C/XM01CK/XM01R For DRN-XM01H/XM01HK Connecting the Unit to the Cigarette Lighter Socket Car cassette deck Using the Car Connecting Pack 1 2 3 4 5 Turn down the volume of the car cassette deck. Set the tape selector to the normal (TYPE I) position, and the DOLBY NR, REPEAT, or BLANK SKIP switch to the OFF position if such are equipped. Insert the car connecting pack into the cassette deck. Start playback on the car cassette deck. Adjust the volume. Connecting the Unit to your Car with a RF Modulator to the +12 V power terminal which is powered when the ignition key switch is in the accessory position Be sure to connect the black earth lead to it first. When the Installation and Connections Have Been Made Securing the Cord After installing and connecting the unit, run cord so as not to interfere with the operation of the vehicle. Run and fix the cord on the passenger side of the center console with the supplied cord clamp. Speaker system Using the Unit on House Current Use the AC power adaptor and the audio cord supplied with DRN-XM01H/XM01HK. Replacing the Lithium Battery into the Remote Commander Replace the battery when the buttons on the remote commander do not work. Remove the old battery and insert a new one. Precautions · Do not install the unit where: ­ the ambient temperature exceeds 55°C (131°F). ­ it will be exposed to direct sunlight or hot air from a heater. ­ it will be exposed to rain, water, or high humidity. ­ it will be exposed to a lot of dust. ­ it will be subject to excessive vibration. · Be sure to turn off the power of each component before making the connections. Fuse (1 A) Black to a metal point on the car Attaching the Home Stand 2 1 to a cassette insertion slot Red Power connecting cord (Supplied) Car audio Antenna connecter Car connecting pack to a cigarette lighter socket If no sound is heard or the car connecting pack is removed, change the playback direction on the car cassette deck. For DRN-XM01C/XM01CK Customers Be sure to check that the voltage of the equipment connected to this unit is correct. Incorrect voltage may cause the equipment to malfunction. · Leave the installed cord clamp for 24 hours before installing the cord. [. . . ] When the receiver is turned on, the RF modulator automatically cuts off the antenna line and directly outputs the sound of the receiver to the car audio with the selected FM frequency. This prevents the sound from disturbing the FM broadcast signal. When the receiver is turned off, the antenna line is connected to the car audio. Besides, you can set the RF modulator to always cut off the antenna line and output the XM radio sound to the car audio, in this case, you cannot hear the normal FM broadcast. [. . . ]