User manual SONY DR-NXM01H

[. . . ] Doing so may prevent the air-bag from functioning properly in the event of an accident. · The installation and use suggestions contained in this manual are subject to any restrictions or limitations that may be imposed by applicable law-- purchaser should check applicable law for any restrictions or limitations before installing and/or operating this product. · Failure to follow these safety instructions and warnings may result in a serious accident. For DRN-XM01C/XM01CK/XM01R For DRN-XM01C/XM01CK/XM01R 6 Digital Audio Receiver Accessory Kit Installation Guide Installing the Cradle in your Car Install the cradle with the supplied car stand. Attach the supplied cover over the base of the stand as shown below. 3 Installing the XM Antenna to your Car The bottom surface of the XM antenna is made of a magnet. Install the antenna horizontally in a location where the radio wave from the satellite is not interrupted by the body of the car (E. g. , roof or trunk lid). Installing the Antenna on the Roof (recommended) XM antenna* Cable guide*** Mounting the Antenna with the Supplied Seal and Cushion with the Double-sided Adhesive Tape 1 Figure of the top Water proof cushion Choose the mounting position, then shape the base of the stand to match the mounting surface. Note Bend the base gently so there are no gaps between the base and the mounting surface. 2 1 Cord clamp** Inside of the trunk Cable guide*** OWNER'S RECORD The model number is located on the bottom and serial number also on the bottom. [. . . ] · Leave the installed cord clamp for 24 hours before installing the cord. Otherwise, the cord clamp may come off because of weak attachment. *** · Cut the cable guide, if required. · It is difficult to attach the cable guide to a body or window which has fluorine resin coating. Cable guide Placement of the car antenna Place the antenna on a flat and even surface on your car roof. The angle from the ground to the satellite should be about 20 - 60 degrees. If you place the antenna on the trunk lid, make sure your car roof does not block the satellite signal. Depending on where you live, you may be able to receive radio waves that are retransmitted by ground repeaters. Leading the antenna cord into the car through the space between door and body When installing the antenna on the roof, you can also lead the antenna cord into the car through the space between door and body. 20° or less For DRN-XM01H/XM01HK Customers WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. 4 for DRN-XM01R only RF modulator (1) Fix the stand with the supplied screws. Note Before drilling holes in the mounting surface, make sure there is nothing behind the mounting surface. 2 Mount the water proof cushion on the back side of the trunk lid. To prevent rain water leakage inside the car along the cord, mount the water proof cushion above the rubber packing when the trunk lid is closed. Cable guide* Water proof cushion INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. · This unit is designed for negative ground 12 or 24 V DC operation only. · Avoid high temperatures, such as direct sunlight or hot air from the heater. · You cannot use this unit with some car cassette deck. · Used with some car cassette decks, the car connecting pack may rattle. This is not a malfunction of the car connecting pack. Note on the DC plug of the car battery cord This car battery cord uses a unified polarity type plug (JEITA standard). Damage will occur if it is connected to a DC power input jack without the !polarity symbol or with another symbol. To Remove the Car Connecting Pack Power lamp Press the Z (eject) button of the car cassette deck. Note You cannot use this car connecting pack with certain car cassette decks. Car battery cord XM antenna Connect it as follows when a diversity antenna is used for the car audio. POWER ANT To the stand receptacle at the bottom of the cradle Tighten the screw at the bottom of the home stand to secure the cradle. 3 1 2 3 Insert a long and thin object into the hole, then pull out the lithium battery holder. Place the lithium battery with the positive (+) side facing up. [. . . ] Note When the unit is not to be used for a long period of time, remove the battery to avoid damage from battery leakage and corrosion. For DRN-XM01H/XM01HK Customers On installing the AC power adaptor Do not place the AC power adaptor in a location where it is subject to: ­ extreme high temperature (E. g. , in a car with its windows closed) ­ direct sunlight or near a heat source ­ mechanical vibration or shock ­ a magnetic field (E. g. , near a magnet, speaker, or TV) ­ excessive dust. Notes · When replacing the fuse, be sure to use one with the correct amperage, as stated on the fuse case. (1 A, 125 V, 20 mm) · Do not use a piece of wire instead of a fuse. · If the replaced fuse opens again, consult your dealer. Warning Use a fuse with the specified amperage rating. Use of a higher amperage fuse may cause serious damage. to the LINE OUT jack to the DC IN 6V jack Specifications Accessories supplied XM antenna (1) Remote commander (1) For DRN-XM01C/XM01CK/XM01R: Car cradle (1) Car stand (1) Screw (5) Cover (1) Water proof cushion (1) Cable guide (3) Cord clamp (4) Cushion with the double-sided adhesive tape (1) Seal (1) For DRN-XM01C/XM01CK only: Car battery cord (1) Car connecting pack (1) For DRN-XM01R only: RF modulator (1) For DRN-XM01H/XM01HK: Home cradle (1) Home stand (1) Audio cord (1) AC power adaptor (1) Optional accessories AC power adaptor AC-E60A Car battery cord DCC-E260 Car connecting pack CPA-9C Setting the POWER SELECT Switch This RF modulator supplies power to the receiver and detects the on/off state by monitoring the load of the power. [. . . ]