User manual SONY CYBER-SHOT DSC-F55

[. . . ] DSC-F55/F55E SERVICE MANUAL Ver 1. 2 2000. 10 With SUPPLEMENT-1 (9-974-166-81) With SUPPLEMENT-2 (9-974-166-82) US Model Canadian Model Tourist Model DSC-F55 E Model DSC-F55/F55E Photo : DSC-F55E AEP Model UK Model Australian Model Hong Kong Model Chinese Model DSC-F55E SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM Table for differences of function Model Destination Video signal Shutter speed DSC-F55 US, Canadian, Tourist, E NTSC Automatic (1/30 ­ 1/10000) DSC-F55E AEP, UK, Australian, Hong Kong, Chinese, E PAL Automatic (1/25 ­ 1/10000) Supplied accessories 1 2 3 1 AC-VF10 AC power adaptor/charger, Power cord (1) 2 A/V connecting cable (1) 3 NP-F10 Battery pack (1) 4 5 6 7 4 DK-115 connecting cord (1) 5 Hand strap (1) 6 Memory Stick (4MB) (1) 7 Lens cap/Lens cap strap (1) 8 9 !º !¡ 8 Sony Picture Gear 3. 2Lite (1) (Compact Disk) 9 PC serial cable (1) !º Conversion plug 3P adaptor (1) UK, Hong Kong model !TM !¡ 2-pin conversion adaptor (1) E model !TM 2-pin conversion adaptor (1) Tourist model SAFETY-RELATED COMPONENT WARNING!!ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! [. . . ] 4) Select page: 6, address: 10, and set data: 59. 5) Select page: 6, address: 01, set data: 3D, and press the PAUSE button. 6) Adjust the GAIN and PHASE of the vectorscope, and adjust the burst luminance point to the burst position of the color reproduction frame. 7) Check that each center of all color luminance points is settled in each color reproduction frame. 8) Perform "Processing after Completing Adjustments". Processing after Completing Adjustments 1) Select page: E, address: 52, set the data noted down at step 2), and press the PAUSE button of the adjustment remote commander. 2) Select page: 6, address: 10, and set data: 00. 3) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 4) Select page: 5, address: F1, and set data: 00. 5) Select page: 0, address: 01, and set data: 00. For NTSC model For PAL model Burst postion Burst postion Fig. 5-1-15. 5-25 12. White Balance Check Mode STILL Subject Filter Clear chart (Color reproduction adjustment frame) Filter C14 for color temperature correction ND filter 1. 0 and 0. 4 and 0. 1 Video output terminal Vectorscope Fig. Strobe White Balance Adjustment Adjust the white balance when the strobe light flashes. Mode STILL Subject Adjustment Page Adjustment Address A plate which reflection rate is 18% (1. 0m from the front of the lens) F 4D, 4E, 68, 69, 6A, 6B Measurement Point Measuring Instrumen Specified Value Checking method: 1) Check that the lens is not covered with either filter. 2) Select page: 5, address: F1, and set data: FF. 3) Select page: 6, address: 10, and set data: 58. 4) Select page: 6, address: 01, set data: 0F, and press the PAUSE button of the adjustment remote commander. 5) Check that the center of the white luminance point is within the circle shown Fig. 6) Select page: 6, address: 01, set data: 23, and press the PAUSE button. 8) Check that the center of the white luminance point settles in the circle shown Fig. 9) Remove the C14 filter, and place the ND filter 1. 5 (1. 0 +0. 4+0. 1) on the lens. 10) Check that the white luminance point stopped moving, and then remove the ND filter 1. 5. 11) Check that the center of the white luminance point settles within the circle shown Fig. [. . . ] Part No. Old Description Remarks Ref. Part No. New Description Remarks 6-1. OVERALL SECTION 6-1 11 3-056-092-01 SCREW, HEAD (2 LOCK) TAPPING 11 3-056-092-02 SCREW, HEAD (2 LOCK) TAPPING * 13 3-056-033-01 SHEET, FLEXIBLE RETAINER * 13 3-056-033-02 SHEET, FLEXIBLE RETAINER 6-1-2. CABINET (FRONT) SECTION 51 X-3949-590-1 CABINET (FRONT) ASSY 51 X-3949-590-3 CABINET (FRONT) ASSY * 56 3-054-960-01 COVER, BATTERY * 56 3-054-960-02 COVER, BATTERY 6-2 61 3-054-961-01 LID, BATTERY 61 3-054-961-02 LID, BATTERY 63 3-056-092-01 SCREW, HEAD (2 LOCK) TAPPING 63 3-056-092-02 SCREW, HEAD (2 LOCK) TAPPING 6-1-3. [. . . ]