User manual SONY DSR-PD150

[. . . ] 3-060-817-12 (1) DSR-PD150 Digital Camcorder Operating Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. Owner's Record The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. ACSerial No. DSR-PD150 ©2000 Sony Corporation Welcome! Congratulations on your purchase of this Sony Digital camcorder. [. . . ] For more information on the drop-frame/non-drop-frame mode, see "Dropframe mode" on page 91. (13) Turn the SEL/PUSH EXEC dial to select TC RUN, then press the dial. (14) Turn the SEL/PUSH EXEC dial to select the desired running mode, then press the dial. REC RUN: Time code value advances only while recording. When making the time code continuous at back space editing, select this setting. FREE RUN: Time code advances freely regardless of the camcorder's current operation mode. For more information on the running mode, see "Making the time code continuous at back space editing" on page 91. 10-12 TC / UB SET TC PRESET UB PRESET TC FORMAT AUTO DF TC RUN NDF TC MAKE UB T I ME RETURN TC / UB SET TC PRESET UB PRESET [MENU]TC FORMAT DF : END TC RUN TC MAKE UB T I ME RETURN 13, 14 TC / UB SET TC PRESET UB PRESET TC FORMAT REC RUN TC RUN FREE RUN TC MAKE UB T I ME RETURN TC / UB SET TC PRESET UB PRESET [MENU]TC FORMAT : END TC RUN FREE RUN TC MAKE UB T I ME RETURN [MENU] : END [MENU] : END To cancel the time code setting Select CANCEL in step 10, then press the SEL/PUSH EXEC dial. To reset the time code Select RESET in step 7, then press the SEL/PUSH EXEC dial. 90 Setting time values Drop-frame mode In the NTSC standard, the time code value is based on 30 frames per second, but the exact video frame frequency is in fact 29. 97 frames per second and the real time, or 18 frames per 10 minutes. Drop-frame mode corrects for this by skipping two frame counts at the beginning of every minute which is not a multiple of ten. In non-drop-frame mode, however, no frame counts are omitted, and there is a gradual deviation of the time code from real time. Making the time code continuous at back space editing Set TC MAKE to REGEN in the menu settings to make the time code continuous when the recording has been interrupted or when the cassette tape has been removed from the camcorder between shootings. When the camcorder is in recording pause mode, the recorded time code is read from the tape and synchronized to the internal time code generator. Once you set TC MAKE to REGEN in the menu settings Even if TC RUN is set to FREE RUN in the menu settings, the running mode is automatically set to REC RUN. Editing 91 Setting time values Setting the user bits value You can set the user bits as eight-digit hexadecimal values (base 16) to have the date, time, scene number, and other information inserted into the time code. (1) (2) (3) (4) (5) (6) Set the POWER switch to VCR or CAMERA. Turn the SEL/PUSH EXEC dial to select TC, then press the dial. Turn the SEL/PUSH EXEC dial to select UB PRESET, then press the dial. Turn the SEL/PUSH EXEC dial to select PRESET, then press the dial. Turn the SEL/PUSH EXEC dial to select the number, then press the dial. (7) Repeat step 6 to set up the other digits. (8) Turn the SEL/PUSH EXEC dial to select SET, then press the dial. 1 POWER 3-8 TC / UB SET TC PRESET UB PRESET TC FORMAT TC RUN TC MAKE UB T I ME TC / UB SET TC PRESET 00 00 00 00 UB PRESET [MENU]TC FORMAT : END RESET TC RUN PRESET TC MAKE RETURN UB T I ME RETURN TC / UB SET TC PRESET 00 00 00 00 UB PRESET [MENU]TC FORMAT : END TC RUN SET TC MAKE CANCEL UB T I ME RETURN VCR OFF CAMERA (CHG) MEMORY 2 MENU [MENU] : END To cancel the user bits setting Select CANCEL in step 8, then press the SEL/PUSH EXEC dial. To reset the user bits Select RESET in step 5, then press the SEL/PUSH EXEC dial. Setting the user bits to the real time clock Set UB TIME to ON in the menu settings. 92 Setting time values Switching the time value TC/U-BIT Editing Press TC/U-BIT. Each time you press TC/U-BIT, the time value changes between the time code and user bits. Note The time code and user bits cannot be displayed properly if the tape does not have time code and/or user bits recordings or if the time code was recorded using a noncompatible method. 93 Superimposing a title If you use a tape with cassette memory, you can superimpose the title while recording or after recording. When you play back the tape, the title is displayed for five seconds from the point where you superimposed it. You can select one of eight preset titles and two custom titles (p. You can also select the color, size and position of titles. SCENE5 (1) Press TITLE to display the title menu in standby, recording, playback, or playback pause mode. [. . . ] 36 Wide-angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 WIPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Write-protect tab . . . . . . . . . . . . . . . . . . . 15 Zebra pattern . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]