User manual SONY DVS-9000SF

[. . . ] SWITCHER PROCESSOR PACK DVS-9000-C DVS9000SF-C PRODUCTION SWITCHER PROCESSOR DVS-9000 DVS-9000SF BKDS-9160 BKDS-9470 BKDS-9161 BKDS-9162 BKDS-9210 MKS-8110SD MKS-8111SD HK-PSU04 OPERATION MANUAL 1st Edition [English] WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. Pour les utilisateurs au Canada (BKDS-9160/9161/9162/ 9210/9470, MKS-8110SD/8111SD, HK-PSU04 uniquement) Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. [. . . ] i DME CTRL (Digital Multi Effects Control) connector (RJ-45) (BKDS-9470) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily to control the various devices from the center control panel. Caution When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. c EXT (extension) connector (BNC type) Used to expand inputs by connecting devices such as an HDS-X series routing switcher. d REF OUT (reference video output) connector (BNC type) Output analog sync signals. e SWITCHER DATA connector (RJ-45) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily for exchange of various types of data (key frame effects, snapshots, etc. ) and still pictures of frame memory. Caution When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. j DME MONI OUT (Digital Multi Effects Monitor Output) 1 to 4 connectors (BNC type) (BKDS-9470) Connectors for four serial digital video signal outputs. These connectors allow you to monitor any desired output signal with the DME signal (video, key, or with graphics). k DME REMOTE (Digital Multi Effects Remote) connector (D-sub 9-pin, RS-422A) (BKDS-9470) When a BKDS-9470 is installed, enables control of DME operations from remote devices. l DME GPI (Digital Multi Effects General Purpose Interface) connector (D-sub 25-pin) (BKDS-9470) Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel. When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. f REF IN (reference signal input) connectors (BNC type) If you wish to synchronize this unit to an external reference signal, input a black burst signal or analog sync signal. The Location and Function of Parts 9 m SWITCHER GPI (Switcher General Purpose Interface) connector (D-sub 25-pin) Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel. n TERMINAL connector (D-sub 9-pin, RS-232C) This connetor is used for factory adjustments. o U (signal ground) terminal Connect to the system ground. p - AC IN (AC power input) A, B, C, D connectors (3-pin) Connect to 100 to 240 V AC power supply with the optional AC power cords. Depending on the system's configuration when shipped, there may be no optional HK-PSU04 Power Supply Units installed. In that case, the AC IN C and D connectors is not used. Caution t MONITOR OUTPUTS 49 to 56 connectors (BNC type) (BKDS-9161) Use these connectors as outputs for primary input monitors or as auxiliary outputs for external devices. These connectors are effective if you wish to output primary inputs with as little delay as possible. For information about installing an HK-PSU04, contact your Sony service representative. [. . . ] Design and specifications are subject to change without notice. EXT Complies with RS-232C standard Data transfer rate: 9600 bps BNC type, 75 S-BUS data transfer rate: 312/1250 Kbps Reference input and output REF IN BNC type, 75, with loop-through output Analog black burst/analog sync BNC type, 75 Analog sync Signal level ±300 mV ±10% Phase variation range -90H to +90H REF OUT DVS-9000 Production Switcher Processor General Power requirements 100 to 240 V AC, 50/60 Hz Current consumption 100 V: 8. 5 A, 240 V: 4. 2A Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (240 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 40 A (230 V) Operating temperature 5ºC to 40ºC (41ºF to 104ºF) Performance guaranteed temperature 10ºC to 35ºC (50ºF to 95ºF) Storage temperature -20ºC to +60ºC (-4ºF to +140ºF) Operating humidity 10% to 90% Dimensions (w/h/d, excluding projections) 482×354×520 mm (19×14×201/2 inches) Mass Approx. 43 kg (9 lb 7 oz) Video input Inputs 17 (BNC type) Signal format SMPTE259M-C Signal level 0. 8 V p-p ±10% Signal tansfer rate 270 Mbps Return loss 15 dB Cable length 200 m (5C-2V cable, BELDEN8281 or equivalent) Video output 24 (BNC type): 1 to 4 and 13 to 16, each with 2 outputs Signal format SMPTE259M-C Signal level 0. 8 V p-p ±10% Signal tansfer rate 270 Mbps Outputs AC input AC IN A, B, C, D 3-pin AC connector Accessories supplied Control connectors RJ-45 Complies with 100Base-TX standard DATA RJ-45 Complies with 100Base-TX standard REMOTE 1, 2, 3, 4 D-sub 9-pin, female Comply with RS-422A standard Data transfer rate: 38. 4 Kbps GPI D-sub 25-pin, female TTL inputs: 8 Relay contact outputs: 4 (30V AC/DC, 0. 1A) Open collector outputs: 4 TERMINAL D-sub 9-pin, female CTRL 75 terminator (1) Bracket (4) Support angle (2) Screw (+B4×10) (8) Screw (+PSW 4×10) (8) Operation Manual (1) Installation Manual (1) Accessories not supplied AC power cord (for USA and Canada only) (125 V 10 A 2. 4 m (8 ft)) (Part No. : 1-557-377-11) AC power cord (for Europe only) (250 V 10 A 2. 4 m (8 ft)) (Part No. : 1-782-929-21) 18 Specifications DVS-9000SF Production Switcher Processor General Power requirements 100 to 240 V AC, 50/60 Hz Current consumption 100 V: 5. 4 A, 240 V: 2. 5 A Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (240 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 40 A (230 V) Operating temperature 5ºC to 40ºC (41ºF to 104ºF) Performance guaranteed temperature 10ºC to 35ºC (50ºF to 95ºF) Storage temperature -20ºC to +60ºC (-4ºF to +140ºF) Operating humidity 10% to 90% Dimensions (w/h/d, excluding projections) 482×177×520 mm (19×7×201/2 inches) Mass Approx. 25 kg (5 lb 8 oz) Analog sync Signal level ±300 mV ±10% Phase variation range -90H to +90H Video input Inputs 17 (BNC type) Signal format SMPTE259M-C Signal level 0. 8 V p-p ±10% Signal tansfer rate 270 Mbps Return loss 15 dB Cable length 200 m (5C-2V cable, BELDEN8281 or equivalent) Video output 12 (BNC type): 1 to 4, each with 2 outputs Signal format SMPTE259M-C Signal level 0. 8 V p-p ±10% Signal tansfer rate 270 Mbps Outputs AC input AC IN A, B 3-pin AC connector Accessories supplied 75 terminator (1) Bracket (4) Support angle (2) Screw (+B4×10) (8) Screw (+PSW 4×10) (8) Operation Manual (1) Installation Manual (1) Control connectors RJ-45 Complies with 100Base-TX standard DATA RJ-45 Complies with 100Base-TX standard REMOTE 1, 2, 3, 4 D-sub 9-pin, female Comply with RS-422A standard Data transfer rate: 38. 4 Kbps GPI D-sub 25-pin, female TTL inputs: 8 Relay contact outputs: 4 (30V AC/DC, 0. 1A) Open collector outputs: 4 TERMINAL D-sub 9-pin, female Complies with RS-232C standard Data transfer rate: 9600 bps EXT BNC type, 75 S-BUS data transfer rate: 312/1250 Kbps CTRL Accessories not supplied AC power cord (for USA and Canada only) (125 V 10 A 2. 4 m (8 ft)) (Part No. : 1-557-377-11) AC power cord (for Europe only) (250 V 10 A 2. 4 m (8 ft)) (Part No. : 1-782-929-21) BKDS-9160 24 Output Board Set General Power requirements 12 V DC Power consumption Max. 50 W Dimensions (w/h) OUT board: 317×380 mm (121/2×15 inches) Reference input and output REF IN BNC type, 75, with loop-through output Analog black burst/analog sync BNC type, 75 REF OUT Specifications 19 Mass CN board: 274×94 mm (107/8×33/4 inches) (using 2 boards) Approx. [. . . ]