User manual SONY DVW-M2000

[. . . ] DIGITAL VIDEOCASSETTE RECORDER DVW-M2000 DVW-M2000P DVW-2000 DVW-2000P Note The supplied CD-ROM includes operation manuals for the DVW-2000 series of digital videocassette recorders (English, Japanese, French and German versions). For more details, see page 1-5 "Using the CD-ROM Manual. " TM OPERATION MANUAL 1st Edition (Revised 1) [English] WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. [. . . ] The most significant digit begins to flash, and the data can be set. 1 2 3 4 Select a clip. Select write protect, mark, or recording start point. The unit enters clip data modification mode. The data entry area begins to flash, and the data can be set. 5 6 7 8 Press the F3 (T) or F4 (t) button until the digit that you want to set starts flashing. Rotate the MULTI CONTROL knob to make the setting. Chapter 7 Tele-File Repeat steps 5 and 6 until you have set all the required digits. The setting is confirmed and the unit returns to clip data display mode. 5 6 Select the data by pressing the F3 (+) or F4 (-) button or rotating the MULTI CONTROL knob. The data setting is confirmed and the unit returns to clip data display mode. Chapter 7 Tele-File 7-9 7-3 Tele-File Menu To make comment settings Proceed as follows to make comment settings. 7-3-4 Undo/Resume Functions Undo function The undo function cancels all modifications and returns the data to the state it was in when first read. Press the F5 (UNDO) button in clip data display mode. Press the F2 (OK) button to execute the undo and cancel all modifications to the data. Resume function If you have not modified any data since the last execution of the undo function, you can press the F5 (UNDO) button again. The button functions as a resume button, which cancels the immediately preceding undo. Press the F5 (UNDO) button in clip data display mode. Press the F2 (OK) button to execute the resume and cancel the immediately preceding undo. 1 2 3 4 Select a clip. The unit enters clip data modification mode. The data entry area begins to flash, and the data can be set. 5 6 7 Chapter 7 Tele-File Enter a character by rotating the MULTI CONTROL knob. Press F4 (t) button to move to the next character place. Repeat steps 5 and 6 until you have entered the entire comment. To delete characters Press the F3 (T) or F4 (t) button until the character that you want to delete starts flashing, and then press the F5 (DELETE) button. To insert characters Press the F3 (T) or F4 (t) button until the character place after the place where you want to insert starts flashing, and then press the F6 (INSERT) button. 8 Press the F2 (OK) button. The comment is confirmed and the unit returns to clip data display mode. 7-10 Chapter 7 Tele-File 7-3-5 Displaying and Modifying Attribute Data You can display and modify attribute data. The example below shows attribute data displayed on the monitor. Video final recording date Title ID Administrator data Model name Serial number Write inhibit setting Thread count Number of cue points Control mode Memory size Amount of memory used TELE-FILE INFORMATION *REC DATE 2001/07/21 TITLE TEST 01 ID ADMIN MODEL SERIAL 00000 WRITE INHIBIT OFF THREAD COUNT 00012 CUE POINT No. 0003 CONTROL MODE panel SIZE 01024 USED 0270 Chapter 7 Tele-File Video final recording date The most recent date (year/month/day) on which video was recorded on the tape. [. . . ] If you move the unit from a cold to a warm location Leave the unit powered off for about 10 minutes, in order to give the unit time to detect moisture condensation. Z ALARM indicator If moisture condensation occurs, "ERR-10" appears in time data display area 1. 14-4 Chapter 14 Maintenance and Inspection 14-5 Regular Checks 14-5-1 Digital Hours Meter The hours meter can display seven items of information, in corresponding display modes, about the operational history of the unit. Use it as a guide in scheduling periodic maintenance. Z Displaying the hours meter MULTI CONTROL knob Display modes of the hours meter H01: OPERATION mode Displays the total number of hours the unit has been powered on in units of 1 hour. F6 (EXIT) button Chapter 14 Maintenance and Inspection H02: DRUM RUNNING mode Displays the total number of hours the drum has run with tape threaded in units of 1 hour. H03: TAPE RUNNING mode Displays the total number of hours the unit has been in fast forward, rewind, playback, search, recording or editing (except for stop and still) mode in units of 1 hour. H04: THREADING mode Displays the total number of times tape has been threaded in the unit. [. . . ]