User manual SONY EMK01

[. . . ] · When the eMarker or the connector become soiled, wipe them with a dry cloth. · Do not pull the cable when disconnecting the cable of the eMarker cradle from your PC. Always grip the plug when disconnecting to prevent damage. · Do not try to pull the cap off without pushing the two buttons on the cap. Specifications Supplied accessories Operating Instructions (1) eMarker cradle (1) CR2025 lithium battery (1) CAUTION KEEP OUT OF REACH OF SMALL CHILDREN. [. . . ] Windows and the Windows 98 logo are registered trademarks of Microsoft Corporation. All other trademarks are trademarks of their respective owners. 4 5 Quick glance If you have any questions about this product, go to the eMarker web site: http://www. eMarker. com. Declaration of Conformity Trade Name: SONY Model No. : EMK-01 Responsible Party: Sony Electronics Inc. Address: 1 Sony Drive Park Ridge, NJ 07656 Telephone No. : (201) 930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3 Step 1 Start by setting up your eMarker. · Download and install the eMarker software to your PC. · Register your eMarker on the web site. See "Inserting a battery" and "Preparations. " Close the lid. Note The eMarker can hold up to 10 eMarks at once. If you try to register an 11th eMark, all 10 black circles will flash to indicate that it is full and the 11th eMark will not be registered. Nothing happens on your PC when you plug the eMarker into the eMarker Cradle. · The "e" logo does not appear on the Task Tray (at lower right-hand corner of screen). t Launch the eMarker application by going through the folder in which the application is installed. · Check to see if your USB port is active by switching it with another device (e. g. a USB mouse). Note All your eMarks will be erased when you open the battery compartment. Be sure to upload your eMarks to the eMarker web site before opening the lid. To cancel an eMark Press the CANCEL button on the rear of the eMarker with the tip of a pen or sharp object. Each time you press the CANCEL button, an eMark is canceled from the latest one entered, and one black circle on the display disappears. Step 2 v When to replace the battery Under normal conditions of use, the battery will last approximately 6 months. When the battery becomes weak, the LCD indications become dimmer. Replace the battery with a Sony CR2025 or Duracell DL-2025 lithium battery. Use of another battery may present a risk of fire or explosion. 5 Take your eMarker to where you listen to the radio and eMark your favorite songs by pressing the e button on your eMarker while listening to radio. · During housework · In a commuter train · On a street Your PC will recognize the eMarker and install the device driver automaticaly. Resister your eMarker. Follow the registering procedure on the eMarker web site. 6 7 If the above-mentioned remedies do not help improve the situation, go to the eMarker web site for more information (http://www. eMarker. com). Step 3 v WARNING Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. Go home and check out the songs that you have eMarked on the web site. Unplug the eMarker from the eMarker Cradle. Be sure to attach the cap to the eMarker after use. ADVERTENCIA Este equipo ha sido probado y se ha comprobado que cumple con los límites para dispositivos digitales de Clase B, de acuerdo con la Parte 15 de las Normas de la FCC. Estos límites han sido diseñados para proporcionar una protección razonable contra interferencias perjudiciales en una instalación residencial. [. . . ] Enchufe el eMarker en el soporte del mismo. Continúe la operación siguiendo las instrucciones de su PC. 3 4 5 Paso 3 v No sucede nada en su PC al enchufar el eMarker en su soporte. · El logotipo "e" no aparece en la bandeja de tareas (de la esquina inferior derecha de la pantalla). t Ejecute la aplicación del eMarker pasando a través de la carpeta en la que haya instalado la aplicación. · Compruebe si su puerto USB está activo conectándole otro dispositivo (p. [. . . ]