User manual SONY FWD-50PX3/ST

[. . . ] To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. On transportation When you carry the display unit, hold the unit itself, not the speakers. If you fail to do so, the speakers may come out of the unit and the unit may fall. This can cause injury. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Display + Remote: Activates a remote commander supplied with the display. Display Unit Only: Disables the remote control function. You can only make settings for the display using the control buttons on the display unit. Remote Only: Disables the controls on the display unit when you want to control it using the Remote Commander only. You can only make settings for the display using the Remote Commander. Note Color System Selects the Color System of video signals. Auto: to set the Color System automatically. NTSC: to display NTSC signals NTSC4. 43: to display NTSC4. 43 signals PAL: to display PAL signals SECAM: to display SECAM signals PAL-M: to display PAL-M signals PAL-N: to display PAL-N signals PAL60: to display PAL60 signals Auto Shut Off When you set this item to "On, " the display unit automatically enters the standby mode when a signal is not input to the COMPONENT or DVI input connectors for more than about five minutes. The display unit automatically enters the power saving mode when a signal is not input to the DVI or RGB input connectors for more than about thirty seconds. While in the standby mode, press the 1POWER switch on the display unit or the POWER ON button on the Remote Commander to switch the display unit on. While in the power saving mode, the display unit is automatically turned on when a signal is input. When operating this item, the modes you can select differ depending on the key you are using. When using ENTER on the Remote Commander for setting, you can select only "Display + Remote" or "Remote Only. " When using ENTER on the display unit for setting, you can select only "Display + Remote" or "Display Unit Only. " 19 (GB) Using On-screen Menus Security Lock Sets the security lock on the display unit. b) VESA is a registered trademark of the Video Electronics Standards Association. c) Mac (Macintosh) is a registered trademark of Apple Computer, Inc. 2 640×480@60 Hz (VESA STD) Macc) 13" VGA (VGA TEXT) Mac 16" Notes 5 800×600@60 Hz (VESA STD) 7 1024×768@60 Hz (VESA STD) 8 1024×768@75 Hz (VESA STD) 9 1024×768@85 Hz (VESA STD) 10 1152×864@75 Hz (VESA STD) 11 Mac 21" 12 1280×960@60 Hz (VESA STD) 13 1280×1024@60 Hz (VESA STD) 14 1600×1200@60 Hz (VESA STD) 15 848×480@60 Hz (VESA STD) 16 848×480@60 Hz (VESA STD) 17 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 848×480@75 Hz 1280×768@60 Hz 1280×768@60 Hz SDTV/HDTV PAL NTSC SECAM NTSC4. 43 PAL60 PAL-M PAL-N 575/50i 480/60i 1080/24psf 1080/50i 576/50p 480/60p 1080/60i 720/60p 720/50P · When inputting an HDTV signal, input the tri-level sync signal to the 2nd pin of RGB/COMPONENT (D-sub 15 pin) on the INPUT2 connector or the BKM-FW12. · If colors appear too light after inputting a DVD signal to the display unit, adjust the "Chroma" setting in the Adjust Picture menu. · When the phase is readjusted, the resolution will be reduced. Actual on-screen display of the unit's status On-screen display 640×480 / 60 (e. g. ) 480 / 60i (e. g. ) NTSC (e. g. ) Out of Range No Sync INPUT1 DVI INPUT2 RGB INPUT2 Component Option 1/2 Video Option 1/2 S Video Option 1/2 RGB Option 1/2 Component Significance The selected input signal is computer RGB. The selected input signal is component video. The input signal is out of the capture range. The signal mode of INPUT1 is set to digital RGB. The signal mode of INPUT2 is set to analog RGB. The signal mode of INPUT2 is set to component video. The signal mode of Option 1 or 2 slot is set to composite video. The signal mode of Option 1 or 2 slot is set to S VIDEO. [. . . ] This function shows the display's condition based on the pattern shown by the flashing of the POWER/ STANDBY indicator. The flashing pattern informs you of the display's current condition. If the POWER/STANDBY indicator flashes, check the number of flashes and contact your authorized Sony dealer. Security Lock enabled! Select Set ENTER Exit MENU If "Invalid password!" appears on the menu screen, start the procedure again from Step 1. INITIAL SETUP/INFORMATION Language: Color System: Auto Shut Off: Security Lock: Information English Auto Off Off 1 Invalid password! Select Set ENTER Exit MENU 4 After completing the process described above, turn off the display unit and unplug the power cord to make the setting valid. The Security Lock becomes activated and the dialog box prompting you to enter the password appears when you turn on the display unit next time. Check the flashing pattern of the POWER/ STANDBY indicator. [. . . ]