User manual SONY GV-M20

[. . . ] Address: 1 Sony Drive, Park Ridge, NJ, 07656 USA Telephone No. : 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] (30 cm) apart, and remove any obstacles between the devices. Infrared rays emitter (back side) The other (recording) VCR Remote sensor 40 Dubbing only desired scenes Digital program editing Confirming the other (recording) VCR operation (1) Insert a recordable tape into the other (recording) VCR, then set to recording pause. (2) Turn the SEL/PUSH EXEC dial to select IR TEST, then press the dial. (3) Turn the SEL/PUSH EXEC dial to select EXECUTE, then press the dial. If the other (recording) VCR starts recording, the setting is correct. When finished, the indicator changes to COMPLETE. 2 OTHERS ED I T SET CONTROL ADJ TEST CUT - I N CUT -OUT I R SETUP PAUSEMODE I R TEST RETURN [MENU] : END Editing ENGAGE REC PAUSE RETURN EXECUTE 3 OTHERS ED I T SET CONTROL ADJ TEST CUT - I N CUT -OUT I R SETUP PAUSEMODE COMPLETE I R TEST RETURN [MENU] : END If the other (recording) VCR operates correctly Skip to step 3 on page 43. If the other (recording) VCR does not operate correctly Set the IR SETUP code, or select the button to cancel the recording pause on the other (recording) VCR. Place your (playback) VCR at least 12 in. (30 cm) away from the other (recording) VCR. Refer to the operating instructions of the other (recording) VCR. 41 Dubbing only desired scenes Digital program editing Step 2: Setting the other (recording) VCR for operation - Using the i. LINK cable (DV connecting cable) When you connect using the i. LINK cable (DV connecting cable) (not supplied), follow the procedures below. (1) Set the POWER switch to ON on your (playback) VCR . (2) Turn the power of the other (recording) VCR on, then set the input selector to DV input. (8) Turn the SEL/PUSH EXEC dial to select "CUT-OUT", then press the dial. (9) Turn the SEL/PUSH EXEC dial to select the average numerical value of OUT, then press the dial. The calculated stop position for recording is set. (10) Turn the SEL/PUSH EXEC dial to select RETURN, then press the dial. Editing 43 Dubbing only desired scenes Digital program editing 6 2, 3 OTHERS ED I T SET CONTROL ADJ TEST CUT - I N CUT -OUT I R SETUP PAUSEMODE I R TEST RETURN [MENU] : END 0 OTHERS ED I T SET CONTROL ADJ TEST CUT - I N CUT -OUT I R SETUP PAUSEMODE I R TEST RETURN [MENU] : END 0 OTHERS ED I T SET CONTROL ADJ TEST RETURN EXECUTE CUT - I N CUT -OUT I R SETUP ENGAGE PAUSEMODE REC PAUSE I R TEST RETUN OTHERS [MENU] : END ED I T SET CONTROL ADJ TEST EXECUT I NG CUT - I N No . 2 CUT -OUT IN I R SETUP +215 PAUSEMODE I R TEST RETUN [MENU] : OTHERS END ED I T SET CONTROL ADJ TEST COMPLETE CUT - I N CUT -OUT I R SETUP PAUSEMODE I R TEST RETURN [MENU] : END 8 OTHERS ED I T SET CONTROL ADJ TEST CUT - I N CUT -OUT I R SETUP PAUSEMODE I R TEST RETURN [MENU] : END 0 OTHERS ED I T SET CONTROL ADJ TEST CUT - I N CUT -OUT I R SETUP PAUSEMODE I R TEST RETURN [MENU] : END 0 Notes If you start recording from the very beginning of the tape, the first few seconds of the tape may not be recorded properly. Be sure to allow about 10 seconds' lead before starting the recording. When you complete step 3, the image to adjust the syncronicity is recorded for about 50 seconds. When you connect with the i. LINK cable (DV connecting cable) You may not be able to operate the dubbing function correctly, depending on the other VCR. Keep the i. LINK connection, and follow the procedure from step 2 on page 38. 44 Dubbing only desired scenes Digital program editing Operation 1: Making the program (1) Insert the tape for playback into your (playback) VCR, and insert a tape for recording into the other (recording) VCR. (2) Press MENU to display the menu settings. (3) Turn the SEL/PUSH EXEC dial to select , then press the dial. (4) Turn the SEL/PUSH EXEC dial to select VIDEO EDIT, then press the dial. [. . . ] 31, 33 Time code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 TV color systems . . . . . . . . . . . . . . . . . . . . . 66 D, E Data code . . . . . . . . . . . . . . . . . . . . . . . . . . . 30, 53 Date search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]