User manual SONY HBA5710

[. . . ] BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE SOFTWARE, OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF. reserves the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein is governed by the terms of a separate user license agreement. This product contains software owned by Sony and licensed by third parties. [. . . ] They are standard RJ-11 female phone jacks. However, the line jack is for connecting to a telephone line that comes from the wall, and the telephone jack is for connecting the computer to a telephone. The modem installed on your computer may differ depending on the configuration you purchased. Line Phone Identifying Components i. LINK (IEEE 1394) Ports 13 The 6-pin i. LINK® port on the back of the system can supply power from the computer to a device if the device also has a 6-pin i. LINK port. The 6-pin port supplies 10 V to 12 V and a maximum power of 6 watts. i. LINK is a trademark of Sony used only to designate that a product contains an IEEE 1394 connection. The i. LINK connection may vary, depending on the software applications, operating system and compatible i. LINK devices. All products with an i. LINK connection may not communicate with each other. operating conditions and proper connections. Before connecting compatible i. LINK PC peripherals to your system, such as an optical disk or hard disk drive, confirm their operating system compatibility and required operating conditions. Refer to the documentation that came with your compatible i. LINK device for information on The 4-pin i. LINK port at the bottom of the front panel does not supply power. 6-pin i. LINK port (IEEE 1394) 4-pin i. LINK port (IEEE 1394) On back of system At bottom of front panel Ethernet Port The Ethernet port on the rear of the system is used to connect to a 100BASE-TX/10BASE-T Ethernet network. Ethernet On back of system 14 VAIO Digital Studio System Reference Manual Expansion Slots There are three PCI slots, two of which are available for expansion (PCI No. The other PCI slot is occupied by the fax/modem card (PCI No. There is one AGP slot that is available for expansion. Slot No. 1 (PCI) Chapter 2 Configuring Your System This chapter contains information on configuring your system. Pull the top of the side cover away from the unit about two inches, then gently lift out the side cover. Removing, Installing, and Replacing Components 25 Replacing the Side Cover 1 2 From the rear of the unit, align the bottom of the side cover so that it slips into the lip on the bottom of the unit. Push the top of the side cover up against the top of the unit until the side cover snaps into position. 26 VAIO Digital Studio System Reference Manual Removing a PCI Add-in Card ! Before opening the system unit, save and close all open files, exit all open applications, turn off the power to all attached peripheral devices, shut down the computer, and unplug the power cord. 1 2 3 Remove the side cover (see "Removing the Side Cover" on page 24). Disconnect any cables attached to the add-in card you want to remove. Remove the screw that secures the add-in card to the chassis. ! Hold the add-in card by its edges and do not touch any components or connector contacts on the card. Static electricity in your body may damage sensitive components on the card. As a precaution, touch any exposed metal part on the metal chassis (preferably the metal part on the power supply) before handling an add-in card to discharge any static electricity in your body. Removing, Installing, and Replacing Components 27 4 Remove the add-in card from the PCI slot and store the card in an anti-static wrapper for future use. Grasp the card with one hand on each end, and gently pull up as you rock the card from side to side. 5 6 If you do not replace the card or install another add-in card, install a slot cover over the vacant slot at the rear of the chassis (see "Covering an Open I/O Slot" on page 41). Replace the side cover (see "Replacing the Side Cover" on page 25). 28 VAIO Digital Studio System Reference Manual Installing a PCI Add-In Card ! Before opening the system unit, save and close all open files, exit all open applications, turn off the power to all attached peripheral devices, shut down the computer, and unplug the power cord. 1 2 3 4 Remove the side cover (see "Removing the Side Cover" on page 24). Remove the slot cover adjacent to the selected slot (see "Removing a Slot Cover" on page 40). Insert the add-in card into the PCI slot. Use a gentle rocking motion, pressing down until the card is fully seated. Align the card's bracket so that the bottom of the bracket fits into the slot at the bottom of the chassis. Make sure that the top of the bracket fits snugly against the chassis lip after the card is fully inserted. Removing, Installing, and Replacing Components 29 5 6 7 8 Replace the screw that secures the card. [. . . ] The parallel port has requested a resource that is already in use. This message is displayed when more than 15 PCI conflict errors are detected. Two devices requested the same resource, resulting in a conflict. Two devices requested the same resource, resulting in a conflict. [. . . ]