User manual SONY HCR-FL7DSW

[. . . ] This system conforms to VIDEO CDs without the PBC functions (Ver. You can enjoy two kinds of playback according to the disc type. You can Enjoy video playback (moving pictures) as well as audio CDs. Play interactive software using menu screens displayed on the TV screen (menu playback), in addition to the video playback function of VIDEO CDs without the PBC functions. [. . . ] This function lets you repeat a single CD or all CDs in Normal Play, Shuffle Play, and Program Play. The following table describes the various repeat modes. To repeat All the tracks on the current CD All the tracks on all CDs Only one track ACTIVE Press PLAY MODE repeatedly until "1 DISC" appears in the display. pLAY MODE repeatedly until "ALL DISCS" appears in the display. REPEAT repeatedly while playing the track you want to repeat until "REPEAT 1" appears in the display. The active picture function is not available when playing audio CDs. Press REPEAT repeatedly until "REPEAT" or "REPEAT 1" disappears from the display. Playing CD tracks in random order -- Shuffle Play You can play all the tracks on one or all CDs in random order. Press PLAY MODE repeatedly until "ALL DISCS SHUFFLE, " "1 DISC SHUFFLE, " or "PROGRAM" disappears from the display. The tracks continue playing in their original order. You can start Shuffle Play during Normal Play by pressing PLAY MODE repeatedly until "ALL DISCS SHUFFLE" or "1 DISC SHUFFLE" appears in the display. You can record tracks from all the CDs in the order you want. When programming, make sure the playing times for each side do not exceed the length of one side of the tape. This function cannot be used during playback of VIDEO CDs with the PBC functions (Ver. Turn the jog dial until the desired track appears in the display. Disc number Track number Total playing time First "STEP" and the programmed playing order appear, then the total playing time appears. The last programmed track Total playing time Note that you cannot use Tape Select Edit for discs containing more than 20 tracks. Repeat steps 5 through 7 to program additional tracks to be recorded on side A. Skip step 5 to select tracks from the same disc. First the required tape length for the CD in the playing position appears, then the total playing time for sides A and B appears. Skip step 5 to select tracks from the same disc. note You cannot use this function when Program Play mode has been set. [. . . ] Noise increases or the high frequencies are missing. Front Speaker: The following measured at AC 220 V, 50Hz DIN power output (Rated) 150 + 150 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (Reference) 200 + 200 watts (6 ohms at 1 kHz, 10% THD) Center Speaker: DIN power output (Rated) 35 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (Reference) 50 watts (8 ohms at 1 kHz, 10% THD) Rear Speaker: DIN power output (Rated) 35 + 35 watts (8 ohms at 1 kHz, DIN) Continuous RMS power output (Reference) 50 + 50 watts (8 ohms at 1 kHz, 10% THD) Inputs PHONO IN (phono jacks):sensitivity 3 mV, impedance 47 kilohms MIC 1/2 (phone jack): sensitivity 1 mV, impedance 10 kilohms VIDEO1 IN (phono jacks): sensitivity 250 mV, impedance 47 kilohms VIDEO2 IN (phono jacks): sensitivity 250 mV, impedance 47 kilohms MD IN (phono jacks): sensitivity 450 mV, impedance 47 kilohms DVD INPUT FRONT, REAR, CENTER, WOOFER (phono jacks): sensitivity 450 mV, impedance 47 kilohms The signal strength is too weak. A stereo FM program cannot be received in stereo. If other problems not described above occur, reset the system as follows: 1 Unplug the power cord. [. . . ]