User manual SONY HANDYCAM HDR-SR5/C HANDYCAM HANDBOOK

[. . . ] To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. [. . . ] For details on turning on the pairing function, refer to the Operating Instructions supplied with the SAIR main unit. 1 Turn on the unit. Press . 5 Press the PAIRING button on the rear panel of the On heat buildup Notice for customers: the following information is only applicable to equipment sold in countries applying EU Directives The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku, Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters, please refer to the addresses given in separate service or guarantee documents. Heat buildup on the unit during operation is normal and is not cause for alarm. Do not touch the cabinet if it has been used continuously at a high volume because the cabinet may have become hot. Do not obstruct the ventilation holes. 2 Set the S-AIR ID of the unit to the same S-AIR ID as the S-AIR main unit to be connected. For details on setting the S-AIR ID of the S-AIR main unit, refer to the Operating Instructions supplied with the S-AIR main unit. unit using a pointed object. When pairing is performed, the S-AIR indicator on the unit flashes and the display changes as follows: "PAIRING" "COMPLETE" 3 Operate the S-AIR main unit to turn on the S-AIR To cancel pairing On the speaker system This speaker system is not magnetically shielded, and the picture on nearby TV sets may become magnetically distorted. In this situation, turn off the TV, wait about 15 to 30 minutes, and turn it back on. If there is no improvement, move the unit far away from the TV. function. For details on turning on the S-AIR function, refer to the Operating Instructions supplied with the S-AIR main unit. Once the connection is established, the S-AIR indicator on the unit lights up and "LINKED" appears in the display for about 2 seconds. Change the S-AIR IDs of the unit and the S-AIR main unit to different S-AIR IDs. To stop the pairing operation midway Press the PAIRING button again. Cleaning the cabinet Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Point the remote at the remote sensor on the unit. Turn on the remote control function. If the STANDBY indicator flashes Specifications Amplifier section DIN power output (rated): 3 + 3 watts (3 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 4 + 4 watts (3 ohms at 1 kHz, 10% THD) The remote does not function. Setting the clock Use buttons on the unit to set the clock. Changing the display Press DISPLAY on the unit. Each time you press the button, the display changes as follows: When the unit is connected to an S-AIR main unit: 6 Press / repeatedly to select the desired option. The default setting is underlined. 1 Turn on the unit. Press . To change the information on the display while the unit is on Turning off the remote control function In addition to the unit you already have, you can connect other S-AIR sub units to a single S-AIR main unit and use them together. 2 Press DISPLAY repeatedly until the clock is displayed. Listening to the sound of the connected S-AIR main unit You can use the S-AIR function to listen to the sound of an S-AIR main unit in a remote location. When the unit is turned off, the clock is displayed. You can turn off the clock display to minimize the amount of power consumed (Power Saving Mode). Press DISPLAY on the unit when the clock is displayed. Press the button again to display the clock. Note The STANDBY indicator on the unit lights up when the unit is off. To turn off the display 7 Press CLOCK/TIMER ENTER . The display shows the timer settings. 3 Press while holding down CLOCK TIMER/ 8 If you selected "ALARM" in step 6, go to step 9. 1 Perform the procedure described in "Establishing the connection with an S-AIR main unit" and check that the S-AIR indicator is lit. If you selected "AUTO" in step 6, prepare the sound source on the S-AIR main unit. For details on preparing the sound source, refer to the Operating Instructions supplied with the S-AIR main unit. ENTER . "RMT OFF" appears in the display and the unit is turned on. If you try controlling the unit using the remote, "RMT OFF" appears in the display and the unit will not accept the signal from the remote. To turn on the remote control function 9 Press to turn off the unit. The unit turns on about 45 seconds before the preset time. [. . . ] Press SLEEP repeatedly. Note Even if you set the timer, no sound is output from the unit if playback on the connected S-AIR main unit ends within the set time period or if communication with the S-AIR main unit is cut off. 1 Press CLOCK/TIMER MENU . "SELECT" flashes in the display. 2 Press CLOCK/TIMER ENTER . 3 Press / repeatedly to select "TIMER. " 4 Press CLOCK/TIMER ENTER . To cancel the timer 3 Press VOLUME +/ to adjust the volume. To operate the S-AIR main unit from the unit You can perform the following operations using the buttons on the remote or unit. To Start playback of a CD/DVD, etc. Select a track, file or chapter of a CD/DVD, etc. Select a preset station when listening to the radio Change the FM/AM band when listening to the radio. [. . . ]